Hey guys, I’ve been getting my 95 c1500 ready for autocross and just regular street driving. The front suspension is nice and stiff with the drop springs I’m using but the back end is really soft. I bottom out a lot and the truck tends to under steer pretty bad. I added a factory rear sway bar...
Howdy and hello from Columbia, SC!
I am the proud owner of a 1999 Chevrolet C1500 Suburban LS - I call it The Bus (pictured below). She's got approximately 319,500 miles on her original engine. I am her fourth owner. I've had to have the timing chain replaced and a new fuel pump installed...
Hi everyone. Wondering if anyone has experience that could help me figure something out that's bugging me. I have a 97 Sierra 1500 with the 4.3 / Automatic transmission. When the engine is hot and I am in drive, foot on the brake and idling, I hear a ticking noise as shown in this video:
Video...
I have this dash cluster that I bought and I’m having issues finding the wiring diagram for the dash cluster for my truck so I can install this one. I have a 20 pin pigtail on my truck and need advice with doing this swap. There is multiple of the same colors and just need help getting a wiring...
She has been my baby. I'm only 19, so I still have quite a bit to learn. This truck was a college gift from my grandparents, and it has probably been one of the greatest things in my life. This truck has had quite a few interesting experiences. Anywhere from mid-highway control arm swap, all the...
Hey Guys! Been a while, but you ain't got rid of me yet ;)
So my bestfriend & I are building his 1990 Chevy C1500 (Single Cab, LWB) that he bought as a roller.
Truck originally had a 305ci & 700R4 from the factory (700R4/4L60 in 1990, call it whatever you want but still just a 700R4)
We put a...
I bought the power window and locks for a 88-94 but have no idea what the pins are for and which control what. If you could help me out that’d be appreciated.
Hi I’m looking to swap out the old bench seat in my 1992 reg cab c2500
What would be the best bet
Ive seen people do new Silverado interior or seats from a king ranch
Any helpful advice would be appreciated
thanks
Hi guys I’m looking for a radiator for a 6.5 diesel but for a 1992 and I can’t find one anywhere on diesel site it shows 1994 and up and I need one for a 1992
Ok this one is pretty simple fellas, so my truck has 202k on the clock, and runs great. But i do worry about the motor so ive used 10w30 synthetic for a while. My boss used that in his 350 so he said it would be good in mine. My question is, for the summer should i use something thicker like...
This is my 89. Stock height, 15x10 with 295/50/r15 all the way around. Looking to fill up the wheel well a get rid of the lip a bit (as much as I love it). I'd like to keep the wheels I have here but am curious what size tire will work best on 15x10 to fill in the well. No clue on the backspace...
In this video, we're going to be replacing the radiator drain plug on my 1994 Chevrolet c1500. For what it’s worth I have the 4.3L V6, but this part also works on the V8 model OBS trucks.
In this video I use the BlueDevil Pour-N-Go Radiator and Block Sealer that I purchased from AutoZone on my 1994 Chevy C1500 with the 4.3L V6 to see if I can fix a coolant leak.
I have a 2000 ccsb c2500 and was looking at doing a spindle lift with 2” spacer and 3”. Body lift just looking to see if it’s doable. Already looking at the upper control arms from airbagit.com
I recently ordered a replacement power seat track for the driver's seat in the '97 C1500 Silverado. Upon removing the driver's seat and the power seat track assembly, I have realized that I might not be able to install the new one (at least not as a direct swap).
The replacement was pulled...
Sorry if this is the wrong place to post this, I couldn't seem to find the best place to post it or any existing posts about this. Anyways, on to the background and question. I was kinda set on installing a 94 cluster into my 88 C2500, as I had had no luck finding a 91 cluster that hadn't been...
Hey guys! Been a while since I've posted anything on my truck and I need some expert help and advice. I have a built 2nd gen LT1 in my C1500 (Originally pulled from a '92 Corvette) and after 4 transmissions in <6 months, It's became evident that the 700R4/4L60's just don't hold up between the...
'89 c1500 5.7 tbi with 700r4
Timing is set to 0
New sensors all around (truck sat for a long time)
Tps sensor is showing .49 volts with key on and not running, once it's started it jumps to 1.3-1.5 volts. Idles high around 1500-1700
When I pulled off the old sensor one of the bolt heads snapped...
1997 GMC Sierra SL 2WD with a 262 4.3L engine, and 4L60E transmission.
Little history of the truck to preface the thread.. The truck was sold in 1996 to my Uncle by my Dad was a vehicle salesman at the local GMC dealership. My Uncle used the truck mainly for various errands, all on...
Texas
1988-1998
C1500 ls swap 3" exhaust
You will need own sensors
Local Pickup, or make shipping arrangements
I have a set up that I no longer need.
Schoenfeld ls1 swap long tubes 3" - mild steel
to 3" y merger
to 3" electric cut out and side dump
to 3" cat
to 3" flowmaster mild steel
to dump...
Getting ready to replace the good 1992 350 with a good 1990 454...I have couple questions
Are the serpentine accessories brackets the same size
Any wiring difference
I know I need 454 exhaust manifold but is the OEM y-pipe different sizes
Any more differences???
Bought the truck with 150k and already driven it to 160k. So far I’ve been fighting a rough idle issue and have replaced
Fuel pump (stock unit)
Tpms sensor
IAC sensor
Coolant temp sensor (for ECU)
Distributor
Ignition coil
Plugs and wires
Spare tire
Rear shackles (0/2)
Exhaust (straight pipe)...
I have two trucks in my garage that I am working on. The donor truck is a 1996 c1500 with 160k. The other is a stripped down 1997 c1500. Same color, same cab, but has a clean title vs the donor which has a salvage title and a bent frame in the front.
Hopefully I can post here to share my...