Members

Caman96

Supporting Member

Supporting Member From Ma

Joined: Jul 17, 2020

Last seen: 14 minutes ago Viewing thread

Latest activity Postings About

- Caman96 replied to the thread xXxPARAGONxXx’s 1999 Chevrolet K2500 Crew Cab.
  
  :cool: Watching. Love the pictures!
  
  Yesterday at 4:56 PM
- Caman96 reacted to xXxPARAGONxXx's post in the thread xXxPARAGONxXx’s 1999 Chevrolet K2500 Crew Cab with Like.
  
  Finally got it. I was able to squeeze this puller attachment just enough in between the bearing and seal.
  
  Yesterday at 2:28 PM
- Caman96 replied to the thread ACD 217-3029 versus SMP FJ504 Fuel Injector Opinions?.
  
  Which is why I ordered what I ordered. I’m confident it’s going to be a Standard Motor Products part. I don’t believe the actual...
  
  Yesterday at 2:06 PM
- Caman96 replied to the thread Tonneau cover.
  
  :321: Yes, 3. Lol
  
  Yesterday at 1:10 PM
- Caman96 replied to the thread Tonneau cover.
  
  Nothing worse than a bed full of snow.
  
  Monday at 2:39 PM
- Caman96 reacted to Joe Dirte's post in the thread Tonneau cover with Like.
  
  Just ordered a roll up off scamazonm had good reviews and only $187. If I was smart I woulda just hoarded the ones I had instead of...
  
  Monday at 2:39 PM
- Caman96 replied to the thread Tonneau cover.
  
  Obviously the supports roll-up with cover.
  
  Monday at 2:27 PM
- Caman96 replied to the thread Tonneau cover.
  
  +2 on the roll up and +1 on the Pop’N’Lock and rail caps.
  
  Sunday at 8:52 PM
- Caman96 reacted to PlayingWithTBI's post in the thread Tonneau cover with Like.
  
  I don't know if they are better but, I like my roll up for a couple reasons - they're less expensive and they don't take up hardly any...
  
  Sunday at 8:50 PM
- Caman96 reacted to Spareparts's post in the thread Good vid on 8 lug hub replacement. with Like.
  
  Got both my hubs changed today. Had to pound a 9 1/6 on one bolt but the rest came without a fight. Front end is a lot quieter now and...
  
  Sunday at 8:49 PM
- Caman96 reacted to jus10inbrla's post in the thread Opinions on Glowshift, MotorMeter, etc gauges with Like.
  
  coming along … just waitin on 52mm hole saw now.
  
  Sunday at 6:00 PM
- Caman96 reacted to 95burban's post in the thread The build of "Wh4t3v3rs" with Like.
  
  Thread seal all NPT. I have to gas sniff and record all my reading then the greenie weenies will come out and check methane levels and...
  
  Sunday at 5:59 PM
- Caman96 reacted to Stumpy's post in the thread The build of "Wh4t3v3rs" with Like.
  
  I use Loctite 545 as the only sealant on air fittings, and got very good service out of it. Stopped using teflon tape a long time ago.
  
  Sunday at 5:59 PM
- Caman96 reacted to xXxPARAGONxXx's post in the thread xXxPARAGONxXx’s 1999 Chevrolet K2500 Crew Cab with Like.
  
  Remoxed driver's-side axle shaft needle bearing with same bearing puller, slide hammer, and heat gun.
  
  Sunday at 5:58 PM
- Caman96 reacted to xXxPARAGONxXx's post in the thread xXxPARAGONxXx’s 1999 Chevrolet K2500 Crew Cab with Like.
  
  Started disassembling the front axle. Removed the driver's-side axle shaft using a slide hammer.
  
  Sunday at 5:50 PM
Show older items
Loading…
Loading…