Komet
Latest activity Postings About
-
-
Found the issue. Years ago I put a battery disconnect on the battery to eliminate parasite drain when I leave it parked for a long time... -
here is a gas one as you can clearly see it has 3 wires
-
this is a sending unit for a diesel notice that the plug only has 2 wires on it were as the gas sender has 3 wires on it
-
Komet reacted to xXxPARAGONxXx's post in the thread xXxPARAGONxXx’s 1999 Chevrolet K2500 Crew Cab with
Like.
Was finally able to find one of the part unicorns for this truck. Incredibly difficult to find a new one. Happened to find it on eBay at... -
Komet reacted to Road Trip's post in the thread SOLVED: Diagnosing/replacing a leaky radiator + flushing coolant (for the inexperienced GMT400 owner) with Like.
It's normal for this to happen as the last little bits of trapped air move from the far corners of the cooling system to the top of the...
-
Magnaflow 3” duals on a buick 350
-
Komet replied to the thread Best deep muffler for 5.7.I get deep tones and no drone from my 36" long 3" single glasspack, but it's very brappy above 3500rpm. Maybe an 18-24" long glasspack...
-
Komet reacted to Schurkey's post in the thread How does electronic timing advance work on a TBI distributor? with Like.
The pickup coil sends a signal to the module 90 crankshaft degrees advanced. The module recalculates the pickup coil signal--retarding...
-
Komet replied to the thread 94 2500 diesel swapp to vortec 350.There is no data producing device in the fuel tank, so I'd say no on that. The fuel level goes straight to the gauge and I don't know...
-
Here's one putting out ~430HP with their heads and a 750CFM carb. You can throw your heads and intake on it. Then, as Erik said, tune...
-
In this case "will not work with" can be subjective. A 383 with a Vortec intake pattern should physically bolt in place. Tuning is a...
-
Can you find out exactly what the muffler shop put on for comparison sake? That or fart louder.
-
Komet replied to the thread Seeking Advice on Restoration.Some good advice here already about rust severity and what to do so I'll just say that the pressure washer is a good first step, don't...
-
Glad to have you with us on the forum! These trucks are great to learn on, and this is a great spot to do research. That being said...
-
Komet reacted to WesternDenizen's post in the thread Suppose this is hello from Washington with Like.
I meant the upper left Washington on a US map lol. Thanks! You moved to a pretty county. Most likely where I'll end up too.
-
-
Loading…
-
Loading…
Members online
- Vikingdude
- Grooter8824
- RacerM95
- Rodney87GN
- cuthstan
- fancyTBI
- ranchman
- KY-N
- Hotwing7
- bradenmitchell
- smdk2500
- dotwell69
- Caman96
- someotherguy
- Wolvrine82
- NC-2500
- Whipped96
- JAR_19
- Chevy44
- rehoward
- Esc1
- Erin
- Komet
- lokitruck
- Remodelmaster
- Turboduck
- Scooterwrench
- Unactive1
- 1Matthias
- jpkinnin
- movietvet
- HeyJay
- TX97z71
- tuffy331
- T1najero
- docstoy
- Drunkcanuk
- studigggs
- Thwartify
- unpredictable1
- offroadtahoe
- 92 Walter
- jjester6000
- Spareparts
- gregge7a
- caw_86
- GrimsterGMC
- Charlesteneows
- Snowman501
- Cadillacmak