Search results

  1. M

    Looking for reco on replacing cast iron heads to aluminum

    I have a 1997 Chevy Tahoe with a 383 and a hot cam . Some one put a set of China vortec heads on it and would like to change. What aluminum heads did you use with a part # please. Thanks Skip
  2. M

    What would happen if

    I remove and plug EGR valve and tube that goes from intake manifold to Header? Thanks in Advance Skip
  3. M

    What size thread on the return line on a 5.7 Vortec

    I am changing over to braided nylon lines and can not determine what size it is
  4. M

    fuel injection feed tubes

    I am looking for the ss feed tubes that go from the injections on top of the engine to the feed and return lines. Please let me know Thanks in Advance
  5. M

    Low Voltage to Fuel pump

    Happy 4th ,I checked my Fuel pump yesterday after install a new pump. I am only getting 8 volts tested before the pump at harness. ??????? Any help would make a good Day Thanks in Advance
  6. M

    metal fuel pump quick disconnects

    I have change my 30 gallon tank in my 1997 Chevy Tahoe. Mine was completely rusted on top ,so new tank pump and wire connector. I need help finding a set of quick disconnects I need sizes and part numbers and who sells them. I am not having any luck Thanks in Advance for you help Skip
  7. M

    What water pump

    I have a 1997 Chevy Tahoe 5.7 Vortec is the water pump a long or short pump. silly question but I do not know. Thanks Skip
  8. M

    Anyone install a roots supercharger on a 1997 l31

    I want to try this. So any help would be great, what Kit tuning etc
  9. M

    I have a baer gt front brake kit and not that happy with the set up.

    I am looking to go bigger (these are two piston) I have 17 inch American racing ralley wheels. Is it possable to go two caliper ? Thanks in Advance Skip
  10. M

    How to fid correct rear wheel bearing and seals

    I install what I was told is a 2005 Tahoe rear into my 1997 Tahoe. I am looking for rear wheel bearings and seals. I ordered a set of Timken bearings for 2005 rear ,But when I tried to install they bottomed out or would not go in any further. They stuck out about 3 /16 of an inch. How do I order...
  11. M

    Looking for new fuel pump assembly

    I am looking for a new fuel pump assembly for my 1997 2 dr 30 gallon tank. Anyone know were I can find one. I have looked all over and cannot find one. Thanks Skip
  12. M

    More Power from my 383 stroker

    Hi I have a 383 stroker built like a GM stroker Cam 431 intake 451 exhaust 9.1 compresstion forger 400 crank Fliud Dampner stock stamped steel rockers Msd ignition Gibson shorty headers. Looking for advice to go up in power specialy low end Aluminum head recomendation Different cam Also I was...
  13. M

    Need a fuel injection fuel line

    Hi I need the fuel and return stainless steel line that bolts to the fuel injector . For a 1997 Chevy 5.7 Vortec Thanks in Advance Skip
  14. M

    What Differential do I have

    Hi I picked up a Coil over control arm rear it is a posie has control arms upper and lower the upper are bent ti fit.Also a rear track bar It has duel piston brake calipier with internal parking brakes. There are numbers stamped on the inside of diff looks like 05027 . Would like to know year...
  15. M

    nbs rear swap into an obs 1997 tahoe

    anyone have done this? Looks like a few ways to make it work. Please can use some help. Thanks in Advance
  16. M

    Summit rear disc brake conversation

    I am removing my summit rear disc Brake conversation. I believe it to be a little Manufacture unit .I have it on a 1997 Chevy 4wd 8.5 rear in my Tahoe. I am going with taller wheels so not be needed the set up. THe unit has about 3000 miles on it. Do not use my truck much anymore. Let me know. Skip
  17. M

    Need advice on a Cowl Hood Please

    Hi I wanted to install a teardrop cowl hood on my 1997 Tahoe. I bought a AMD Hood and it is out of square and does not match curves of fenders sticks up about 1/8 of and inch in the center of fenders. My Truck I have owned since new and it has never been in an accident. Anyone have some better...
  18. M

    %.7 Hard to start when warm

    1997 Chevy Tahoe 5.7 Starts fine when really cold,After that hard to start (have to turn over about 10 seconds. I was told that if I open throttle body plate a little bit will fix. Anyone ever done this? if so how much? and will this also raise idle? Thanks in Advance for the help
  19. M

    Looking for big brake converstion

    I have a 1997 4wd Chevy Tahoe. I just installed 18 in wheels .So i am looking for aproven large brake conversation kit that will give me finnally good brakes. I am looking to convert to rear disc brakes also. Please help so I can make a good first choice. Thanks in advance
  20. M

    Hard To Start

    I have a 1997 Chevy Tahoe with a 383 msd digital box new spider injection good fuel pressure, What would make engine hard to start? After starting warms up about 30 seconds runs fine. Thanks in Advance for any input
  21. M

    Anyone install a torque storm supercharger on a l31?

    I talked with them and they said I would have to change to an early sbc serpentine belt set up to make it work. Any help?
  22. M

    Doing Bus with [email protected]

    I reco This member very highly Knows his parts fair priced and quick delivery. I will be buying more
  23. M

    Abs poss.swap

    Can I swap a 2000 1500 tahoe or suburban abs unit into my 1997 Tahoe? What would have to be changed? I did the 2000 tahoe master, baer front brakes and rear disc swap but still looking for better braking. Thanks in Advance I am collecting parts to go 2000 rear disc set up because now have...
  24. M

    Problem with making engine run

    Hi I had a bad miss fire. Had a friend put his scanner on it and showed bad tps sensor,coolant temp sensor, Changed both with oem Delco Started truck 1997 Tahoe 5.7 and still ran bad with rough idle. Put scanner on again now showed bad maf Changed that . Now truck will not start at all and shows...
  25. M

    What is this wire for?

    I have a white with a blue tracer coming out of the white connector on the pcm. It is cut and overlapped taped together (not connected together) What is the wire for and why would someone cut it? Thanks in Advance

Latest posts

Members online

... and 5 more.
Total: 1,639 (members: 55, guests: 1,584)

Forum statistics

Threads
64,360
Messages
1,392,103
Members
51,485
Latest member
DonnieBhn

Share this page

Top