A/C compressor turns on and off?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
I don't know whether the previous owner had the AC working but when I went to add a half can of refrigerant, the compressor would kick on and off every 2 seconds. In addition to that, when I removed the hose from the low pressure port, you can hear an audible hiss coming from the port leaking refrigerant, don't know if that's normal. Any help is appreciated, thanks. The AC knob is set to max and the AC button is pushed in. My 6.5 does rev down a bit when the compressor kicks in.
 

Dariusz Salomon

I'm Awesome
Joined
Jun 4, 2020
Messages
1,423
Reaction score
4,055
Location
UK,Oxford
Hi-first question is-what is your ride? Second-do you know how long was the AC empty? If over a year then I'd start with replacing seals(o rings) and valves. Also add PAG (oil)with dye-it will save you some money as if the system is leaking you will lose the gas but at least it will show you where does it leak from.
The "every 2 seconds" compressor's action is due to the fact that there's little gas in the system if I'm not mistaken.
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
Hi-first question is-what is your ride? Second-do you know how long was the AC empty? If over a year then I'd start with replacing seals(o rings) and valves. Also add PAG (oil)with dye-it will save you some money as if the system is leaking you will lose the gas but at least it will show you where does it leak from.

Hey there, it is a 96 K3500 single cab with a 6.5 turbo diesel. I unfortunately don't know how long it has been empty for. I don't work with engines at all so replacing o rings and valves would be something of a great challenge, but if it isn't too difficult, I can definitely give it a try. Maybe a full video or a walk through of how to do this would be great. Thanks
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
I think it cycles on and off because there's no refrigerant in the system. That would probably make sense in this case, although an overcharged system would also show the same symptoms too. I highly doubt that its overcharged though because the truck was neglected for some time. I'm wondering though why after I charged the system and removed the hose from the low pressure port, why does the port hiss and leak refrigerant back out? Does the black cap that screws onto the port stop it from leaking?
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
Usually if it kicks on and off like that it is overcharged.
Not necessarily, it could be either. If it's low, the low pressure switch will open when it gets below 20 - 25PSI. When you get too much pressure the high pressure shutoff switch will open but that's closer to 330+ PSI but, it'll need to be hot with high ambient temps. OP - you need to put pressure gauges on it to see what's going on. If it's been sitting for over a year without a charge, you'll need to replace the receiver,/dryer and orifice tube (at a minimum). Then, evacuate the system for at least 30 minutes, shut off the vacuum pump and see if it holds a vacuum. Then you can start charging the system with the factory recommended R130A amount.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
I'm wondering though why after I charged the system and removed the hose from the low pressure port, why does the port hiss and leak refrigerant back out?
Your Schrader valve is bad and needs to be replaced. The cap is only there to keep it clean. You can't rely on it to stop a leak.
 

Aparke4

I'm Awesome
Joined
Nov 4, 2019
Messages
202
Reaction score
208
Location
CA
Your Schrader valve is bad and needs to be replaced. The cap is only there to keep it clean. You can't rely on it to stop a leak.

This^

My A/C, 96 k2500 was blowing warmer and warmer and I topped it up using a fix a can from autzone but the system didn't take that much oil/ freon. Took it to a local firestone and the leak tested and sure enough- shcrader valve was culprit. They did an extraction and refill and its ice cold.
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
I'll be buying a vaccum kit with gauges soon to see what's going on. I was watching a couple videos last night on fixing this sort of stuff and it's not too complicated after all.. I'll be replacing the low pressure port and change out a couple o rings. And quick question, why replace the dryer? Does it go bad after years of no ac?
 

Dariusz Salomon

I'm Awesome
Joined
Jun 4, 2020
Messages
1,423
Reaction score
4,055
Location
UK,Oxford
Since it's a single cab then your system is much more simple then dual ac-so good news here.First try to tightening the valves using pliers-you just grab and twist-then add some refrigerant and see if it hisses no more. I'd still replace them anyway.
As to dryer-read the insert. I just took a screenshot with explanation-I don't promote these guys.
Orifice tube for piece of mind and also to check if it contains any bigger chunks of metal and stuff-that will indicate any compressor damage.

You must be registered for see images attach
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
First try to tightening the valves using pliers-you just grab and twist-then add some refrigerant and see if it hisses no more. I'd still replace them anyway.
You can go to O'Reillys and get a kit with valves for both low and high side. The low side is the same size as a regular car tire valve but the high side is bigger. You need this tool in this picture to remove and install them since a normal tire valve tool won't fit the high side. Here's the 2 kits.
You must be registered for see images attach


Here's what you get in the cap and valve kit
You must be registered for see images attach
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
Alrighty got it, thanks for the help guys. I saw a video online of a guy turning the pulley/clutch of the compressor while the engine is off, but I'm not able to do it with mine. Don't know if that's normal. The compressor does kick on but the engine revs down quite a bit. Also, which o rings do I replace? All of them? Thanks again in advance, I'll begin work on the ac system in the coming weeks.
 

Dariusz Salomon

I'm Awesome
Joined
Jun 4, 2020
Messages
1,423
Reaction score
4,055
Location
UK,Oxford
Id say all-the ones on the pipes going to compressor(on top),idk where orifice tune is in yours but that one too(mine is in joint pipes on the right hand side near battery),dryer one.
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
Edit: My plan is to use one of these kits to fix the leaking Schrader valve I mentioned originally, the orifice tube, and the dryer, as well as replacing a couple o rings. I will vacuum the system and test to see if it maintains vaccum, and then refill with UV freon to see if there are any leaks. I will update in the coming weeks as I'm quite busy with work.

I won't replace the lines going between the compressor and accumulator/dryer as it's just the Schrader valve that I suspect is leaking the most, not the piping itself.

You must be registered for see images attach

You must be registered for see images attach
 
Last edited:

thinger2

I'm Awesome
Joined
Jul 6, 2019
Messages
2,437
Reaction score
6,929
Location
Tacoma
All of the above and, the ac clutch adjustment is really touchy.
It takes a special tool and it is kind of a pain to do.
You can get a loaner tool to do this from the part stores.
Once you fix the leak and pull a vacuum and all of that and get a proper charge.
It might engage and still slip.
Look for aluminum dust out of the clutch.
Sometimes that clutch is worn or burnished to the point that it just wont engage long enough to build pressure.
It skips because it is a pretty weak electromagnet that pulls the clutch in.
Its been awile but I seem to recall the allowance was .015 to .030?
Fairly tight for an open to air clutch.
You can replace just the clutch on the compressor.
It is doable.
If you end up going that route let me know .
The adjustment is a pain but you can do it.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
Its been awile but I seem to recall the allowance was .015 to .030?
Fairly tight for an open to air clutch.
You can replace just the clutch on the compressor.
It is doable.
It's about 0.020 - 0.035" AND I found a new NAPA R4 clutch @ >0.080" which promptly smoked itself after a week! Here's what I went through during my experience with one of my R4 compressors. It's not that hard measuring the air gap, the best way is to have 2 sets of feeler gauges, one opposite the other to achieve the proper gap. The air gap is adjusted by just tightening the nut or hitting it with a socket to close the gap, originally there were no shims used on it. in this thread I also went in to adding a relay to get full battery voltage to the coil. It turned out 11.4 VDC wasn't enough to hold the clutch in place.
This finally got my A/C to work properly. YMMV:33:

https://www.gmt400.com/threads/swapping-the-clutch-on-an-r4-a-c-compressor.49928/
 

Tornexted

OBS Enthusiast
Joined
Mar 29, 2021
Messages
53
Reaction score
22
Location
New York, NY
Quick question, I assume the orifice tube on my 2-door truck is located behind the front grill right before the condenser? Where else could it be if it's not there? I hope I can begin work on the AC this Thursday if everything from amazon comes in on time.
 

Forum statistics

Threads
78,031
Messages
1,643,900
Members
81,074
Latest member
Rod knock
Top