Members

GoToGuy

I'm Awesome From CAL

Joined: Sep 16, 2020

Last seen: Today at 5:50 AM

Latest activity Postings About

- GoToGuy replied to the thread Security light blinking.
  
  Whatever year it is , did you refer to the OE service manuals if there is any other steps to go with the cylinder replacement?
  
  Today at 5:44 AM
- GoToGuy replied to the thread 4 high and 4 corner mod.
  
  Yeah, I liked my dually running lights. But high beams all the time? High beams switched on with low, yes
  
  Today at 5:41 AM
- GoToGuy replied to the thread How to rotate the crankshaft?.
  
  Oh, forgot that small detail.
  
  Today at 5:36 AM
- GoToGuy replied to the thread Anyone upgraded a full float 14 bolt to disc brakes?.
  
  Incoming!:biggun::gr_guns:
  
  Yesterday at 7:23 PM
- GoToGuy replied to the thread intake heater inlet; saveable??.
  
  The design for lower pressure hose, the wedge barbs bite into hose to retain hose on fitting. Wrenching down clamps on barb fittings ...
  
  Yesterday at 7:16 PM
- GoToGuy reacted to 1990_C1500Brian's post in the thread Use GM motor mounts 90 C1500 with Like.
  
  So I am swapping a 350 in place of the tired 305. I putt anchor motor mounts and the mounts wouldn't allow the engine to drop in. The...
  
  Yesterday at 6:51 PM
- GoToGuy replied to the thread Rough idle after oil pressure sensor replacement.
  
  So what you should done. Recheck everything you touched. Before buying new parts. Wires in correct positions. A rough idle? Recheck...
  
  Yesterday at 6:41 PM
- GoToGuy replied to the thread noob.
  
  After a long term storage , I would suggest complete tuneup, oil, filters, power steer fluid, flush brake fluid with new. Axle lube...
  
  Yesterday at 6:23 PM
- GoToGuy replied to the thread How to rotate the crankshaft?.
  
  Is there still corrosion built up on the cylinder walls? It only takes a little and the rings hit the rust and stop like a brick wall...
  
  Yesterday at 6:18 PM
- GoToGuy replied to the thread Dim lights everywhere.
  
  Why would you assume anything. Have checked the output voltage of the Alternator? What's the battery voltage? The fact everything is...
  
  Yesterday at 7:33 AM
- GoToGuy replied to the thread Super HIGH idle after multiple parts replacement.
  
  Are doing all this from memory? Were any parts actually failed malfunctioning? Did you go through the adjustment procedure for kickdown...
  
  Yesterday at 7:25 AM
- GoToGuy replied to the thread Got a 96 GMC Sierra,had the 5.7 I've swapped it to a 5.3 just try to find a color coded pin out for the gauge cluster so I can hook up gauge wires ..
  
  Did you check the sensors and senders are compatible with older truck?
  
  Yesterday at 7:01 AM
- GoToGuy replied to the thread Got a 96 GMC Sierra,had the 5.7 I've swapped it to a 5.3 just try to find a color coded pin out for the gauge cluster so I can hook up gauge wires ..
  
  Search the engine thread for OE service manuals. Follow the link to download the free PDF. Chapter 8 , Electric. Has all circuits, all...
  
  Yesterday at 7:00 AM
- GoToGuy replied to the thread Barn Find IROC-Z.
  
  I don't remember where got them , the set I have that are six ton not raised are the height of fully raised three ton. . The new six ton...
  
  Yesterday at 6:53 AM
- GoToGuy replied to the thread Hazard lights not working.
  
  Are any of you reading the answers ? If all the exterior lights are working normally, is there a problem with the exterior grounds...
  
  Yesterday at 6:33 AM
Show older items
Loading…
Loading…