Search results

  1. V

    np261 no power

    I have a 2000 Silverado 4L80E swap, NP261 manual shift transfercase. Well I found that 4wd is not working, no dash light saying its in 4wd. Checked fuses with a test light and all are good. Checked for power at the 3wire switch on the transfercase and had no power there. Also checked for power...
  2. V

    4L60E rebuild kit

    Trying to sell a rebuild kit for a 4L60E. This is the kit - http://www.ebay.com/itm/200722335758?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 - I paid $360 for it about a month ago, still all in the box and brand new. Looking for $280/OBO. Just want to get it out of the way and try to...
  3. V

    looking to buy 05 ... advice?

    I found a 05 ECSB 5.3L, 164k miles, fully loaded interior. It has a decent sized dent in the drivers bed side, but it looks like it could be punched out. It does have surface rust, but I figured that could be cleaned up since its caught early enough. The dealership is only asking $4995. I will...
  4. V

    Few new parts for sale, located in VT

    Since I no longer have a frame/truck, I am looking to sell a few parts from my build. All parts are new unless specified as used 4L60E Master Rebuild kit (http://www.ebay.com/itm/200722335758?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649) - $300 shipped, just bought at the end of March...
  5. V

    help me build my 350 tbi

    I have been in the process of doing a complete tear down of my truck. The frame broke, so figured its time to redo everything. I have a few parts on their way for the truck, but now I am trying to figure out parts for the engine itself. I already have 062 vortec heads on their way (rebuilt)...
  6. V

    frame snapped in half ... what now?

    So I was working on replacing the leaf springs in my truck (from 1/2ton leaves to 3/4ton) and when I got one side out, the frame snapped in half..... I parked the truck to rebuild the engine,transmission, and to work on a few other things to restore it. Then this happened... If I decide to weld...
  7. V

    rebuilding 350 advice

    I have started picking up parts for my 350 and 4L60E rebuild. I got the 4L60E rebuild kit on the way from Oregon transmission. So now I am working on the 350. I ordered some 062 vortec heads, and I am looking for a decent cam (roller). I am assuming I have roller rocker arms - but will...
  8. V

    Two tone my truck

    I was curious if anyone was able to two tone my truck for me. I am trying to figure out paint ideas for new paint. I am thinking these two paints Green - http://www.ebay.com/itm/370597356375?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649 Metallic Black -...
  9. V

    94 K1500 build part 2

    So the start of nice weather for 2012 has started, and that means time to tear down my truck again. This is the first picture of when I picked her up for $700 (it was either $600 or 700, cant recall). After Tropical Storm Irene hit us in Vermont, I was financially hit hard - lost most...
  10. V

    rear disc conversion kit

    I have been researching how to convert from drums to discs and I came across this kit - http://www.cutthroat4x4.com/catalog/product_info.php?products_id=56 - I know it says its for a 14bolt FF, where mine is the SF, but would it still fit? I am assuming it will work with 6lug as well, since I...
  11. V

    4L60E Interchangability in years

    I just picked up a 2000 4L60E for a really good deal. I was curious how hard it would be to swap into place of my old tired 4L60E? I did notice the front of the transmission housing was slightly different - the entire case were the torque converter goes is one piece under neath, where on mine...
  12. V

    decent vortec heads?

    I was curious if these heads would work, and decent priced for swapping onto my 350 ... http://www.ebay.com/itm/270797692034?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649 I have been looking around for the past month but want to make sure I am getting a decent deal. Tax returns so time...
  13. V

    guide to rebuilding 4l60e

    I was curious if anyone knew of a decent guide that I could read before tearing apart a 4l60E. I am looking to rebuild a 4L60E to handle some power, and heavy duty towing, as well as a 1500mile trip to Florida in the summer of 2013. I have looked on amazon for a book specifically for this, but...
  14. V

    gauges for gauge pillar

    I have had a 3gauge pillar pod, and have only had 2 gauges in it for the past 4-5months. Now I am looking for a third, and not sure what to get for my truck. Any ideas? Right now I have transmission temp, and fuel pressure. I can't decide on vacuum or air/fuel ratio(although I can monitor this...
  15. V

    Time to install new Leafs, got couple questions

    So my stock 1/2ton leaf springs broke on me, the bottom leaf cracked in half so time to replace them. I picked up 3/4ton leaf springs from a friend for $50, and they are in good shape. He also had some Polyurethane bushings brand new - http://www.summitracing.com/parts/ENS-3-2128R/ - my question...
  16. V

    Stepside bed damage

    I have been looking for a bed for my truck and got an email about this step side. The person is asking $400, and sent me the following pictures. Only damage looks to be the rear corner. Now I have very little fiberglass experience, but I have patched up fiberglass fenders before. My question is...
  17. V

    short bed located near Vermont

    Well it has come time for me needing a bed ASAP. I will take either step or fleet side, as long as its a short bed, prefer with a tailgate but not mandatory. Condition is not a huge thing, need something that isn't rotted to the ground, something with a few dents and dings are fine. Paint does...
  18. V

    brake reservoir question

    Is the small front portion of the brake fluid reservoir for the front brakes or the rear brakes? I can't remember which it is. The reason I ask is because I have a big leak somewhere, but can't find it - and just the small front section in the reservoir goes empty. The back section of the...
  19. V

    Possibly moving to FL

    I may be moving to the Lake Worth, FL area around July/August. My job is moving, and I have the option of going (keeping my position), or staying here in VT and lose my job. I was kind of curious how people like the area, if there is anyone from the area on here. I have only been to FL once, and...
  20. V

    decent torch for cutting?

    So - as the title says, do you think this torch will work for cutting the torsion bars out of my truck? I have been trying to find a new torsion bar mount but can't find anything around me - even the junkyards are empty. Reason I need a torch is my bars are stuck - and I have tried heating them...
  21. V

    Next step for more TBI power...

    So right now I have done most every mod that can be done with my 350 TBI, and I am curious what my next step for more power would be. I have done the Ultimate TBI mods, FPR @ 18psi, custom tune, open element filter, injector and throttle body spacers, full exhaust, headers, etc. What is the...
  22. V

    custom cluster idea

    For Christmas I took my truck on a 140mile trip to family for the holiday, and on the way down my speedometer kept getting stuck at 50mph, then if i hit the dash it would go to 65mph (i was doing 65mph, and tunerpro showed 65mph), so I think the speedometer is getting stuck on itself some how. I...
  23. V

    help identifying this rim?

    I was wondering if anyone was able to help me identify this rim? I have a set of 4 which were giving to me by a friend. He said they were on a 97 K1500, but no idea on the brand. I do know they are 15"x7" wide, and they bolt right up to mine, so chevy 6lug bolt pattern..... other then that I...
  24. V

    4l60e lost OD/lockup

    So I was out shopping earlier, and my servo cover popped out (i replaced the stock servo with a vette one around 1500miles ago). The cover only popped out to where you could see the first O-ring. So I pushed it all back on and put the clip back together, and its held in. But now I noticed that...
  25. V

    transmission or gears for better highway driving

    This past weekend I drove in a friends NBS chevy, and noticed he could do around 75-80mph on the highway and still be around 1500-2000rpms in overdrive. It rode a ton nicer then mine as well, I was just curious if it was just a matter of gears, or a better transmission to get mine to drive...

Latest posts

Staff online

Members online

... and 11 more.
Total: 1,859 (members: 61, guests: 1,798)

Forum statistics

Threads
64,390
Messages
1,392,848
Members
51,554
Latest member
goosebandit

Share this page

Top