I have finaly collected most of the parts I needed to start the SAS on my 92 ECSB Chevy. This next week I will be getting my springs in along with all the stuff for my hydro steering. Tomorrow I'm going to order my detriot lockers and 4.56s front and rear. it should be 9" in front and 8" in the back.
What I would like to have done still Is get the bed sprayed w/ rhino liner(or the like), I would also like the have the quarter panels rhino lined. Then I need a new motor. The list goes on with odds and ends, but It will slowly come along.
This is the list of stuff I have so far...
78 dana 60 kingpin front.
87 dana 70 rear.
ORU SAS kit +6" in spring length.
16x10 Black steel rims.
Kingpin rebuild kit.
New pads/ shoes for the brakes.
new ujoints for the axle shafts.
37x13.50 mickey thompson Baja Claws.
4.56s Front & Rear.
Detriot lockers F/R.
Hydro steering stuff.
Draglink.
Steering arm.
Tie rods.
Brake lines.
Hub Bearings.
Ubots and Ubolt plates.
Ujoint rear axle.
Front driveline.
Shocks.
The rims
The rear d70
The front d60
I still need to mod the exhaust a little...
Well this is where she sits as of right now, althought not pictured. I do have the front spring mounted on one side of the hanger.
Got my tires...
I got alot done on the D70 lastnight, But I forgot the damned Ebrake cable. So I get to pull the drum off again and put the damned cable in. O'well atleast its eazy...
Waiting on the gears still, I also need new hub bearings. I new I was missing something:LOL:
I'm useing an old spring pack and jack to lift the springs to mount them
BTW the Pass side of the truck is a ***** to drill holes in.
I still have alot of tweaking to do, but I'm getting real close to being done. I have the PS gear box drilled and tapped. I have all the brake lines. I need to finish my new tie rod and drag link. I need to make a trac bar. I need to finish removing the BL and all the crap along with it, ect,ect,ect...
What I would like to have done still Is get the bed sprayed w/ rhino liner(or the like), I would also like the have the quarter panels rhino lined. Then I need a new motor. The list goes on with odds and ends, but It will slowly come along.
This is the list of stuff I have so far...
78 dana 60 kingpin front.
87 dana 70 rear.
ORU SAS kit +6" in spring length.
16x10 Black steel rims.
Kingpin rebuild kit.
New pads/ shoes for the brakes.
new ujoints for the axle shafts.
37x13.50 mickey thompson Baja Claws.
4.56s Front & Rear.
Detriot lockers F/R.
Hydro steering stuff.
Draglink.
Steering arm.
Tie rods.
Brake lines.
Hub Bearings.
Ubots and Ubolt plates.
Ujoint rear axle.
Front driveline.
Shocks.
The rims
You must be registered for see images attach
The rear d70
You must be registered for see images attach
The front d60
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
I still need to mod the exhaust a little...
You must be registered for see images attach
Well this is where she sits as of right now, althought not pictured. I do have the front spring mounted on one side of the hanger.
You must be registered for see images attach
Got my tires...
You must be registered for see images attach
You must be registered for see images attach
I got alot done on the D70 lastnight, But I forgot the damned Ebrake cable. So I get to pull the drum off again and put the damned cable in. O'well atleast its eazy...
You must be registered for see images attach
Waiting on the gears still, I also need new hub bearings. I new I was missing something:LOL:
You must be registered for see images attach
I'm useing an old spring pack and jack to lift the springs to mount them
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
BTW the Pass side of the truck is a ***** to drill holes in.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
I still have alot of tweaking to do, but I'm getting real close to being done. I have the PS gear box drilled and tapped. I have all the brake lines. I need to finish my new tie rod and drag link. I need to make a trac bar. I need to finish removing the BL and all the crap along with it, ect,ect,ect...