Search results

  1. CountyLineGarage

    Power box

    Apologies if you’ve seen this twice, posted on the dumb questions sticky and didn’t get any activity so I’ll post here instead. Probably been covered I suppose but fresh opinions never hurt… I’ve got a system I’m wiring up in my toolbox. I’ve run 2 gauge cable to the box from my battery (on my...
  2. CountyLineGarage

    Convenience center piggyback

    I’m planning on putting in a switch panel for some future additions to my “service truck” build. The plan is to add some work lights, a power inverter and a 12 volt compressor (the latter two will be controlled by switched relays hopefully controlled by the same panel) I want to use a...
  3. CountyLineGarage

    Hitch part number

    Howdy, just looking for a part number for a proper hitch for my k1500. It’s a short bed so I’d like the spare to still be able to fit and my current hitch is set too far forward to be sleek or hidden, this puts the cross bar in the way of the spare. I was just curious if anyone has the part...
  4. CountyLineGarage

    Step bars

    So I’ve searched around this site for a sticky with info regarding side steps for our trucks and have found some good stuff regarding steps for an extended cab 2 door (but I do have a question) I was curious if the cab mounts are the same distance apart on a single cab as the front two on the...
  5. CountyLineGarage

    Obd 1 scanner options

    I’ve got a 95 gmc k1500 with a random reoccurring code 32 (a common goose chase on these guys according to our identifix program at work and this site) Point is I’d like to get a scanner for data retrieval. I have a moates aldl cable but I don’t like to use my laptop. I’d rather use a...
  6. CountyLineGarage

    Diag Help

    My 95 Sierra (350, 4x4, automagic trans) has a longer than normal crank, a spark knock in 1st -2nd gear after being driven a while and a code 32 that I’ve replaced the egr valve for (not solenoid yet). And it shows in our old snap on brick scanner that it’s running lean. Question is where...
  7. CountyLineGarage

    Egr part numbers?

    Does anyone know the proper part number (ac delco) for an egr valve for a 1995 k1500 (350) I’ve read a bunch of stuff and they offer a few options from delco so I was just curious which one it is. Original is long gone replaced with a parts store repop so crossing it isn’t an option I don’t think?
  8. CountyLineGarage

    4x4

    I’ll start by saying I have a new actuator (electric type not thermal) and the on the floor selector. These all work. The problem arrives when the actuator “actuates”. You can hear it wine but it’s almost like it keeps bouncing off the shift fork inside the axle housing for lack of a better...
  9. CountyLineGarage

    Rear window seal/fix

    Not sure if this is the proper thread but I noticed a rattling noise the other day going down the driveway and realized it was coming from the rear glass. It appears the lower seam of the whole sliding glass unit is detaching itself from the cab of my truck. I was curious if that’s a common...
  10. CountyLineGarage

    Overheating issue...

    I’ve got a 95 Sierra I just replaced manifold gaskets on. I also replaced the thermostat just cause they’re cheap and why not... I bled the system of air a few times though I’m confident the first time worked as no air came out after that I just wanted to be sure. But, (there’s always a but)...
  11. CountyLineGarage

    Floor mat options

    Howdy, does anyone know of a set of floor liners like you can get from weather tech for these trucks. Weather tech doesn’t make a set and I don’t know any other brands that make a decent cut floor liner. Thanks guys!
  12. CountyLineGarage

    Gauge repair/replace

    So recently my oil pressure gauge took a crap. Sending unit is good and I also hooked up a mechanical gauge for assurance and installed a high volume melling oil pump when I rebuilt my motor. So I know for a fact it’s the gauge or at least something after the sending unit. The gauge is...
  13. CountyLineGarage

    2.5 in lift Shocks Suggestions

    So I lifted my truck with torsion keys, add a leaf in back, and some rough country upper control arms. I was just wondering which bilstein shocks I should use for this little bit of lift I’ve installed. I also would like to mention that the shocks from tough country make contact with my bump...
  14. CountyLineGarage

    Oil Pressure upgrade

    Howdy! I rebuilt my 95 Tbi 350 and wondered if the oil pressure I’m getting is satisfactory. It’s around 20 sometimes a little lower once it’s idling warm @around 500-600 rpm. I don’t have any knocking or anything that I’d think would come with a bad bearing. If I must I can drop the pan and...
  15. CountyLineGarage

    Radiator questions

    I’ve got a 95 k1500 Sierra that I need to put a radiator in. I’m not pushing anything crazy so a stock rad will do but does anyone know what the little tube coming out of the radiator running underneath the overflow line is. It’s capped off redneck style right now because the stupid rubber cap...
  16. CountyLineGarage

    Broken 4x4 Dangit Chevy!!

    Hey there! I’ve got a 95 k1500 4x4 obviously with the floor shifter. I replaced the actuator with the plastic motor variety but am still unable to get my orange light to come on and 4x4 to engage in either gear. Any other suggestions?
  17. CountyLineGarage

    Grill Options

    Probably could find a thread on this If I wanted but I like a fresh one for new opinions or updated info. Anyway does anyone know if the old style grille (88-93) can be made to fit the later 90s trucks. I have a 95 that the grill is cracked on so I’m looking into options. I really like the...
  18. CountyLineGarage

    Grill Options

    Probably could find a thread on this If I wanted but I like a fresh one for new opinions or updated info. Anyway does anyone know if the old style grille (88-93) can be made to fit the later 90s trucks. I have a 95 that the grill is cracked on so I’m looking into options. I really like the...
  19. CountyLineGarage

    Coolant temp changing

    Hi not sure if this has been addressed but I recently rebuilt my 350 tbi for my truck and have aluminum heads (not sure if it matters). But the coolant temp gauge keeps showing it get cool down to the big line before 210 and heating up to just under 210 it fluctuates up and down quite a bit...
  20. CountyLineGarage

    Tuning Tbi (for probably the thousandth time)

    I recently rebuilt a 350 TBI for my 95 Sierra. It’s got summits 62cc aluminum heads and lunatis barebones efi compatible cam and lifters and flo tech headers run to 3 inch pipe. It runs great. Just a little bit of surge on idle not sure if it’s the cam or something else(any advice is welcome...

Latest posts

Members online

Total: 1,408 (members: 50, guests: 1,358)

Forum statistics

Threads
64,355
Messages
1,391,984
Members
51,476
Latest member
Rwr3814

Share this page

Top