Erik the Awful
Latest activity Postings About
-
-
Erik the Awful replied to the thread 1992 7.4 Oil?.Felix Wankel patented and produced a rotary pump in the 1930s. Being an engineer he immediately realized it could be used as an engine... -
Erik the Awful replied to the thread Budget headers.Everybody thinks inflation is new and that we had thirty years of low inflation, but if you look at American made products, the...
-
Erik the Awful replied to the thread 1997 c1500 5.7 carb.Do not use roller lifters with a flat tappet cam, nor flat tappet lifters with a roller cam. Shelve that cam and get a roller cam...
-
I’d see if Crager has that size listed as an option for the soft8. $200 is a lot for a single steel wheel. Yikes
-
Erik the Awful replied to the thread Upper Intermediate Steering Shaft.Did you use the single u-joint version or the two u-joint version? If you used the single u-joint you should be fine.
-
Erik the Awful reacted to Jskingry's post in the thread AC Blower not working even after replacing resistor with
Like.
Well I tested with a ground straight from the battery and nothing so I replaced the blower motor and it's working again blowing harder... -
Erik the Awful replied to the thread Part replacement Advice.Safety and reliability first. I have a stock of other parts on hand to put on WCJr and Roscoe, and whenever tackle serious work I...
-
Erik the Awful replied to the thread Gt45 t4 turbocharger on stock 350 tbi 5.7.Not in current practice, and that paper fails to convince me he knows how. He's basically proposing to put an alternator on the blowoff...
-
Erik the Awful replied to the thread High volume oil pump 98 K1500 5.7.Engine Masters had a pretty good episode recently (S8E13) where they tested different weights of oil to see how much power they robbed...
-
Erik the Awful reacted to HawkDsl's post in the thread Write up: Floor Shift, Non-Tilt Column Disassembly 88 - 94 with Like.
Here is a picture of the key release spring (Item 1 in this write up): The bit that looks like it's in the way of a screw hole is...
-
Erik the Awful replied to the thread 1992 7.4 Oil?.The rotary engine was an offshoot of the rotary pump, not the rotary valve. Rotary engines are fantastically efficient and reliable when...
-
Erik the Awful replied to the thread AC Blower not working even after replacing resistor.You have a loose wire, loose connector, or loose ground. It is possible that the wiring inside the blower motor is loose, but you need...
-
Erik the Awful replied to the thread Bagged and bodied 99 c3500 build.Please keep in mind where your chest is going in an accident. Build that so it won't crush or impale you if the column doesn't collapse.
-
Erik the Awful replied to the thread Sniper fuel line return.I'm running the Sniper in my '89 through the factory fuel lines with no problems. I'd send that throttle body back and have tell them to...
-
Erik the Awful replied to the thread The herd grows.Hmm... $800 difference between the 390 hp 350 and the 436 hp 383. That's not a cheap upgrade.
-
-
Loading…
-
Loading…
Members online
- OutlawDrifter
- Erik the Awful
- Reega
- Drunkcanuk
- echoxozzy
- mwilliams55555
- Remodelmaster
- 8898addict
- Das Hatt
- thweneb06
- 0xDEADBEEF
- truedual93
- bentlyw
- Chevyguy2000
- Sebyschevys
- Joe Dirte
- Alteca
- TylerZ281500
- Cuckfield
- stockcarkid3
- Caman96
- Coothethird
- df2x4
- Charlie Vortec
- termite
- DeCaff2007
- Kraken
- 95burban
- 62barsoom
- BuiltToWork
- Old77
- Rock Hard Concrete