Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
What do you think of the gov-lock itself? I had one in my Yukon with correct lube and it only worked when it felt like it, never when I really needed it, and I was always scared it was going to explode. Is that mainly an 8.5" thing?WHAT AXLE?
I'm well-known on this forum for my distain of the "10-bolt" 8.5" ring gear axle assembly, especially the pickup-truck versions that have the terrible rear brakes. I think they're totaled when they need fresh axle grease.
When it was my '88 K1500, the weak and worn-out 8.5" open differential axle assembly got removed. I found a much-stronger 9.5" six-lug axle with OEM Gov-Lock "Posi", the right gear ratio, and bigger, better brakes. Refreshed the brakes, popped a "conversion" U-joint into the rear of the driveshaft, had everything installed for about $500--$600.
I've had the G80 on my 99 1500 2wd NBS and it's always worked fine...again, always used it on pavement, and not gunning it if I ever went off-road. But they do have a bad reputation for blowing up.What do you think of the gov-lock itself? I had one in my Yukon with correct lube and it only worked when it felt like it, never when I really needed it, and I was always scared it was going to explode. Is that mainly an 8.5" thing?
Are you aware if the 2018 Silverado LT featured the g80 govlock for the limited slip differential? Those seem to work pretty well when they are new.
I'm not "thrilled" with the 9.5 Gov-Lock. It was abrupt when it engaged, even just going around corners. It softened-up some as I put miles on it. It had been parked for some unknown amount of time before I bought it.What do you think of the gov-lock itself? I had one in my Yukon with correct lube and it only worked when it felt like it, never when I really needed it, and I was always scared it was going to explode. Is that mainly an 8.5" thing?
Don't know a thing about them.Are you aware if the 2018 Silverado LT featured the g80 govlock for the limited slip differential? Those seem to work pretty well when they are new.
The Gov-Lock is a clutch-type, but with a speed-governed control mechanism.However mechanically locking differentials, such as the automatic G80 locker are better off-road in slippery terrain IMO.
I reckon a swap to a G80 axle would satisfy in this situation.
Beware of the number of axle splines vs. spider gear splines. GM made the 8.5" ring gear pickup truck axles bigger (from 28 spline to 30 spline???) in or around 1989.I managed to find an Auburn style posi out of a 90s Caprice cop car in the junkyard and it was a direct swap in my 8.5" 10 bolt. I kept my existing ring and pinion and was able to perform the whole swap on the cheap relatively.
The Auburn cone-type style can be freshened but you need to think outside the box because service parts are not available. When they go bad it's because the face of the cones have bottomed out in the case and the sides of the cones no longer grip. Disassemble, machine .050-.060 off the outboard side of the cones, shim the gear side correspondingly with what is a non-rollerized cam thrust washer as they are hardened material(My Mopar literature is packed away for the time being or I might be able to provide a part#). Some guys will put the cones on lathes, or mill, and others have ghetto grinded them. It's not a critical surface you just need to make some room so the cone is not bottomed out in the case. The trick is upon reassembly. You need an axle in both sides to line up the up the inner and outer splines on each side as you're putting the case halves back together.I managed to find an Auburn style posi out of a 90s Caprice cop car in the junkyard and it was a direct swap in my 8.5" 10 bolt. I kept my existing ring and pinion and was able to perform the whole swap on the cheap relatively. The downside is those units are not rebuildable so you just have to hope you find one that isn't too worn out.
FIFY.If you’re keeping the same gears, so that you don't replace or disturb the pinion gear, installing a posi carrier yourself isn’t a big job.