93 K3500 Fuel/performance problem

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Acesneights1

Newbie
Joined
May 22, 2021
Messages
4
Reaction score
0
Location
Connecticut
I recently got a 1993 K3500 Dump with a 454 TBI. Truck starts good, idles ok and runs ok on flat ground light thottle. It feels like its starving for fuel when I hit a hill, i went under the truck to change the fuel filter only to find out the PO felt the truck didnt need one and bypassed it.....So I am assuming the TBI unit is probaly damaged. I have no idea how to trouble shoot this thing since I work on mostly diesels. Also can I just rip the TBI setup off and throw a carb on it ? Its old enough to be exempt from emissions here and over the weight anyway so no problem with that. Just need a running reliable truck.
 

Acesneights1

Newbie
Joined
May 22, 2021
Messages
4
Reaction score
0
Location
Connecticut
I didnt see any obvious place to attach a fuel pressure test gauge. I don’t have a DA5 adapter for my Solus Edge to scan it ut the Mil light is off and I dont think these older trucks have much for testing I can do with the Edge anyway ?
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
I didnt see any obvious place to attach a fuel pressure test gauge.
You can "borrow" a fuel pressure test gauge (for TBI) from an auto parts store. Usually you hook it up where the fuel filter goes. You should have 10 - 13 PSI on a 93, IIRC 94 - 95 7.4L were 18 - 20 PSI.

There is plenty of data you can get from these OBDI systems with the right scanner or software and laptop. We were just talking about it on this thread, go to post #8 and see. @Schurkey posted a link to another thread where he shows what a "red brick" can do too.

https://www.gmt400.com/threads/engine-shutting-off.53235/
 

smdk2500

I'm Awesome
Joined
Dec 26, 2017
Messages
1,670
Reaction score
2,834
Location
Nebraska
I didnt see any obvious place to attach a fuel pressure test gauge. I don’t have a DA5 adapter for my Solus Edge to scan it ut the Mil light is off and I dont think these older trucks have much for testing I can do with the Edge anyway ?
You sure can use your edge with the correct adaptor. That is what I use on both my 95's
 

Acesneights1

Newbie
Joined
May 22, 2021
Messages
4
Reaction score
0
Location
Connecticut
You can "borrow" a fuel pressure test gauge (for TBI) from an auto parts store. Usually you hook it up where the fuel filter goes. You should have 10 - 13 PSI on a 93, IIRC 94 - 95 7.4L were 18 - 20 PSI.

There is plenty of data you can get from these OBDI systems with the right scanner or software and laptop. We were just talking about it on this thread, go to post #8 and see. @Schurkey posted a link to another thread where he shows what a "red brick" can do too.

https://www.gmt400.com/threads/engine-shutting-off.53235/
I have a Mac tools fuel pressure test kit. Ill have to see if it has the adapters but the PO bypassed the fuel filter with homemade rubber lines from the tank. This thing is a mess. So was there a test port on the lines or do I t in ?
 

smdk2500

I'm Awesome
Joined
Dec 26, 2017
Messages
1,670
Reaction score
2,834
Location
Nebraska

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,611
Reaction score
27,201
Location
The Seasonally Frozen Wastelands
...and be careful, because the threaded connector on the fuel pressure tester may not have the same thread size as what the TBI adapter has on it's Schrader valve.

I wound up buying a Schrader valve to convert my TBI adapter to the same thread size as my gauge unit.
 

LC2NLS6

I'm Awesome
Joined
Apr 23, 2019
Messages
277
Reaction score
235
Location
MI
I wouldn't even diagnose, I'd replace the fuel pump (verify its getting goo voltage too), fix the fuel filter situation, and pull the TBI unit and carefully tear it down to the baskets in the injectors and clean it up. Putting it back together, be super extra double top secret careful, they are fragile as glass tightening the injectors back on...
 

RichLo

E I E I O
Joined
Jan 6, 2015
Messages
5,209
Reaction score
10,431
Location
Wisconsin
Yep, TBIs are just as easy as carbs to rebuild, just fix it an forget it. And worst case you'll need new injectors but that is still less $$ than a new carb.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,598
Reaction score
29,580
Location
Tonopah, AZ
Looks like there is a screen on the tbi ? Im assuming at the fuel inlet ?
There are 2 screens on each injector. One that slides up around the bottom and a tiny one that goes in a hole in the side.
You must be registered for see images attach
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,611
Reaction score
27,201
Location
The Seasonally Frozen Wastelands
Yep, TBIs are just as easy as carbs to rebuild
Much easier.

No tiny fuel or air passages to unclog, or to verify as free-flowing. No idle mixture screws. No need to dick with the idle speed screw most of the time.

No adjusting of float level, choke pulloff, choke tension.

The worst part of rebuilding either would be re-bushing the throttle shaft. 2-barrel carb to 2-barrel TBI, not much difference either way.
 

Erik the Awful

Truly Awesome
Air Force Supporting Member
Joined
Aug 9, 2019
Messages
10,036
Reaction score
23,505
Location
Choctaw, OK
When I was a tech, I interned with a coworker who had been a GM tech. I bought an '81 Camaro with a Quadrajet on a 305 and one of the first things I did was rebuild the carburetor. No sooner did I finish and he whipped out a wooden box full of Q-Jet specific tools. He spent an hour and adjusted everything to spec. It ran perfect, but it took an expert an hour to set it up right. Fuel injection is absolutely superior.
 

lindy55

Newbie
Joined
Apr 21, 2021
Messages
1
Reaction score
0
Location
Auburn Washington
Quadrajets are okay when they work right. They can be a problem. On the other hand, I've bolted on a lot of edelbrocks that ran great for years right out of the box. Sorry but I'd rather have a carburetor than fuel injection. Even racing, I'm out there running while the guys are sitting there trying to dial in there injection system to match the conditions. That's my opinion.
 

Latest posts

Staff online

Forum statistics

Threads
78,033
Messages
1,643,921
Members
81,075
Latest member
gmt400isking
Top