Members

Schurkey

Supporting Member

Supporting Member From The Seasonally Frozen Wastelands

Joined: Jan 14, 2018

Last seen: Today at 1:44 AM

Latest activity Postings About

- Schurkey reacted to Komet's post in the thread I love plastic engine parts! with Like.
  
  Vise grips and pull while twisting would be the first thing I'd do. Assuming it comes out, I'd chase the threads with a tap and insert a...
  
  Today at 12:57 AM
- Schurkey reacted to JDGMC's post in the thread I love plastic engine parts! with Like.
  
  Buy a cast aluminum timing cover as a backup. Once you have it in hand have at it. Make a wedge by grinding down a flat piece of metal...
  
  Today at 12:57 AM
- Schurkey replied to the thread Control arm.
  
  Perhaps a moderator will move this thread from "ENGINES" and into "Stock Suspensions + Bolt On Kits". Given a choice, I'd rebuild the...
  
  Today at 12:46 AM
- Schurkey replied to the thread 97' Silverado 5.7 ext.cab rwd MAP SENSOR.
  
  Connect scan tool, drive vehicle. Watch MAP sensor reading as you vary the throttle. The harder the engine is working, the more...
  
  Today at 12:32 AM
- Schurkey replied to the thread 454/ 4L80 install question.
  
  If you're installing the trans with the engine...have the vehicle jacked WAY up so there's room for the trans to hang down as the engine...
  
  Today at 12:10 AM
- Schurkey reacted to SNCTMPL's post in the thread Front diff need modifier? with Like.
  
  This is from my 16 Duramax. It is the 9.25.
  
  Yesterday at 10:16 PM
- Schurkey replied to the thread 5.7L TBI stalling and low idle help.
  
  Classic symptoms of the rocker arm adjusting nuts being WAY TOO TIGHT. Back off, find zero lash by wiggling the pushrod UP AND DOWN...
  
  Yesterday at 10:14 PM
- Schurkey replied to the thread Front diff need modifier?.
  
  What "newer Chevy" has a front differential with a cover? Photo?
  
  Yesterday at 5:44 PM
- Schurkey replied to the thread Confirmed brake bleeding scan tools.
  
  WHICH ABS UNIT? The older EBC4 has two manual valves that need to be dicked-with DURING THE SCAN TOOL BLEEDING PROCESS. The later...
  
  Yesterday at 5:39 PM
- Schurkey replied to the thread ABS MODULE.
  
  Was it properly bench-bled? Doing a decent job takes more time and effort than most folks realize. Which "brake light" are you talking...
  
  Yesterday at 1:45 AM
- Schurkey reacted to RichLo's post in the thread ABS MODULE with Like.
  
  What makes you think the ABS module is bad? That doesn't initially sound like a module problem unless you have done more diagnosis...
  
  Yesterday at 1:38 AM
- Schurkey reacted to Caman96's post in the thread ABS MODULE with Like.
  
  Did you bleed the ABS with a scan tool? I never consider what the brakes feel like with the engine off.
  
  Yesterday at 1:38 AM
- Schurkey replied to the thread Front diff need modifier?.
  
  There is no "cover" on an IFS front differential. You could play games with aerosol brake cleaner in the fill hole, with the drain plug...
  
  Yesterday at 1:37 AM
- Schurkey replied to the thread Reverse Level 1996 GMC sierra INFO NEEDED.
  
  Why screw with the ride-height at all?
  
  Yesterday at 1:33 AM
- Schurkey replied to the thread Sway bar link angle and popping noises..etc.
  
  WHAT VEHICLE??? Must be a TBI-era SUV since you're showing external ABS speed sensors. CV axles, installed with the bigass nut...
  
  Yesterday at 1:31 AM
Show older items
Loading…
Loading…