Search results

  1. Reega

    K2500 CCSB carrier bearing(s)?

    2000 K2500 350 80e ccsb: I’m not certain of the nomenclature, but is the red arrow pointing to a carrier bearing? I’m used to them being midway between driveshaft halves. Are there 2? Looking at rock auto and other sites, I’m having trouble identifying this part. The rubber is destroyed in...
  2. Reega

    AC Rebuild Input please-condenser yes or no

    ‘00 K2500, 350, 4l80e. Current is HT6/H6 compressor. Two cans R-134a with dye and the only spots I can find are in the compressor. Looks like common “belly leak”. First can I shot in had dye, didn’t realize it also had stop leak. Current replacement list is: Suction/Dishcarge lines Orifice...
  3. Reega

    2000 Duramax wheels-center cap

    Sorry if this doesn’t belong here. Okay, Duramax wheels circa 2000. Painted black, with black center caps. I want to run chrome/polished aluminum lugs. Thoughts on keeps the center caps on without the threaded lugs? Also open to other black center caps if they fit. 9.5 14 rear so I don’t...
  4. Reega

    4l80e throttle from stop, no movement then dies

    98 K2500 4l80e 350, this very well might not be a tranny problem, but I need to get input from my peers that are much wiser than myself. 2 times from an idle, in gear-stopped, I push the accelerator pedal and the engine revs, but there is no forward movement. Out of habit, I take my foot off...
  5. Reega

    88-89 Braided Fuel Line Routing

    Pulled the fuel lines( stainless braided PTFE) to have them new ones built at a local place and noticed two clamps ( one on the feed and one on the return) were not mounted. It appears they most likely attached on the back of the block somewhere. Also, there is what looks like a heat shroud...
  6. Reega

    99 K2500 Crew Cab(Problems to look for)

    I'm in talks to buy one of these and realized my knowledge about GMT400s was mostly based around the TBI years as that is what my family has had and I currently have. From what I can tell you get a 4l80E and 9.5 14 bolt pretty much across the board. The one I am looking at is a 350. What...
  7. Reega

    Wrench Wrecked-Correct Starter??

    89 K1500 4L60 350 I had the flywheel replaced several years ago. Told it was an 85 block and flywheel based on casting numbers. My starter is loud, not like any other GMT400 I have heard or any other vehicle for that matter. When I say starter, I mean the engagement and process of starting...
  8. Reega

    Holley Projection 300-49-worth putting on?

    Apparently I bought one a long time ago and forgot about it. Found it today cleaning out the garage. Is this thing worth putting on? My truck is stock except headers/exhaust and TBI mods. Should I just throw it on Craigslist? The threads I searched showed people ran them back in the day, but...
  9. Reega

    Timing Advanced....Vacuum Leak

    89 GMC K1500 350 700R4 So a couple of years ago I replaced my timing chain and gears, stabbed the dizzy, and tried to set timing @ 0 degrees. EST unplugged. It would fire and die. Slow advancing of the dizzy got it to start, run, and idle “okay”. Somewhere around 20 degrees. Kept searching...
  10. Reega

    Low fuel pressure-is my test accurate

    89 GMC K1500 350 700R4 My truck starts but dies almost instantly. If I give it about half the pedal, it’ll kinda run, but sounds like it’s doing everything it the world to try and die and does as such shortly. I hooked up my Actron gauge at the back of the TBI- it’s not on the return line I...
  11. Reega

    4WD Roar....Growl...Noise

    So I have an ‘89 K1500, 350 700R4 3.73 front and rear. As it was happen, there was slippery stuff this weekend. I put in 4wheel high, with some effort...had to go 4wheel low first-to test in case stuff got dicey. There was a noticeable roar, growl, other synonyms-the front drivetrain. As of...

Latest posts

Staff online

Members online

Total: 1,326 (members: 38, guests: 1,288)

Forum statistics

Threads
64,350
Messages
1,391,912
Members
51,470
Latest member
dkeyes25

Share this page

Top