Search results

  1. chevyrider838

    Cunningham Machine Upper/Lower Steering Shafts?

    @Cunningham Machine I ordered the Cunningham lower a while back for my ‘99 K1500 Classic and it’s great, however, I’m trying to install the Cunningham upper now but I’ll need to turn steering wheel 90 degrees to insert the upper into the steering shaft at the steering wheel. Website states that...
  2. chevyrider838

    Lower ball joints different sizes???

    While installing the new lower ball joints on my 99' K1500 with 6" RC lift, my mechanic informed me that the passenger/driver sides are different. Meaning, the passenger side will accept the larger Moog K6509 but the driver side will only accept the smaller Moog K6477. How can this be so and has...
  3. chevyrider838

    Sway bar links for RC 6" lift?

    Hi guys, I'm interested in replacing the sway bar links on my 99' K1500 Classic w/ 6" lift as the bushings look like there just about shot. Do I need to buy sway bar links specifically for a 4-6" lift or will stocks be ok? If I need extended ones, any suggestions? Thanks
  4. chevyrider838

    Steering wheel snap-ring?

    Replaced my ignition switch but forgot to reinstall the snap-ring on the steering column under the 21mm bolt. Will that be ok, is it a safety issue or should I pull steering wheel off again and reinstall? Thanks for the
  5. chevyrider838

    Codes after a/c replacement

    99 K1500. Replaced compressor, a/c hoses, accumulator, condenser, upgraded to 140 alternator, belt drive tensioner, and serpentine belt. Speedometer and rpm gauge aren’t working. Also experiencing slow acceleration from stop as if the truck is in a higher gear and getting codes PO0740, P1860...
  6. chevyrider838

    A/C vacuum down still?

    Hello. I'm replacing my a/c compressor, a/c hoses, accumulator and condenser. Is it still necessary to vacuum down before I recharge after these parts are installed. I was thinking that everything that would have moisture is being replaced right? Or no? Thanks for the help guys!
  7. chevyrider838

    Engine/Alternator Whine Issue!

    Installed an old school Kenwood KVT-696 along with the BT-200 bluetooth box in my 99' K1500. Had terrible engine/alternator whine so I re-ran the grounds and the whine remains. Amplifier is on the rear cab wall, grounded to the jack box screw and the h/u is grounded directly to the battery. I've...
  8. chevyrider838

    Rotational grind noise???

    At around 40mph and let off the gas, I hear a loud rotational grind that continues until speed decreases, then when I give it a little gas the noise starts again then disappears with increased speed. Sounds like it’s coming from the middle to rear of truck. Differential, transmission...
  9. chevyrider838

    New power steering pump question?

    I’m looking to get a new power steering pump for my ‘99 K1500 but not sure if I need to get one with EVO or without. I’ve heard horror stories about EVO but not sure. Ordering a Blue Top steering gear as well and they need to know EVO or not. What do you guys think?
  10. chevyrider838

    Bad headlight switch? Led?

    Just installed an led bulb in my headlight switch and now noticed that when the dimmer wheel is all the way down...the truck chimes as if the lights are on. Could this be a bad switch or the effects of the led bulb? Thanks
  11. chevyrider838

    3rd Brake Light issue!

    Previous owner was using a single socket/bulb setup using the 2 white wires behind 3rd brake light lens and it was working. I disconnected it to install a led 3rd brake light but it wasn’t plug in play so I decided to go back to factory assembly but using all 4 bulbs. In the meantime, I twisted...
  12. chevyrider838

    Third brake light leds?

    Has anyone experienced any issues switching your bulbs to leds in your factory third brake light assembly? Thx!
  13. chevyrider838

    88’ steering gear box work in 99’ obs?

    Are these interchangeable? Any turning ratio differences? Thanks
  14. chevyrider838

    88-98 vs 99-06 speakerbox???

    Has anyone placed a 99-06 under backseat speaker box in a 98 extended cab? What is the fitment difference vs the 88-98 version? Thanks
  15. chevyrider838

    88-98 10-bolt 4:10 front/rear gear kit???

    Which 4.10 kit would you recommend for 88-98 k1500? Send links if possible...thanks so much!
  16. chevyrider838

    Gear ring and pinion kit?

    Was interested in buying a pinion gear kit and wanted to know how to determine my carrier bearing fitment? Thanks!
  17. chevyrider838

    Is this a sensor?

    Changed out spark plugs and noticed this beside the #8 plug on passenger side...looks like a sensor but doesn’t have anything plugged in it. Does it supposed to....don’t see a loose connector anywhere. Thanks!
  18. chevyrider838

    Replace all? Drums, cylinder, bearings and seal?

    I’m about to replace my rears drums, hardware kit and cylinders and was wondering if I should go ahead and replace the bearings and axl seals while I’m there. There not leaking so should I just leave them alone? Thanks
  19. chevyrider838

    Which bushing kit???

    Need a front bushing kit for my ‘99 OBS but not sure if I need to purchase kit for a ‘98 or a ‘99. The pic of the ‘99 bushing kit shows NBS truck. They have different part numbers but are they the same? What do you suggest? Thanks
  20. chevyrider838

    Connector with orange tag?

    Removed my dash bezel for stereo install and while putting back together I notice a lone connector with an orange tag attached. I don’t see where it goes....what is it? Thanks!

Latest posts

Members online

Total: 1,903 (members: 50, guests: 1,853)

Forum statistics

Threads
64,357
Messages
1,392,065
Members
51,483
Latest member
zzz71

Share this page

Top