1994 GMC C/K 1500 6.0l lq4

[OBS94]

Picked this Truck up a couple weeks ago doing a engine rebuild with Mayhem Motorsports. Should have it back in a few weeks. Pretty stoked, not sure what kind of power she will put down. Will be largely dependent on what the transmission will hold.

My end goal is 1000whp and a 8 second 1/4 pass

Mayhem Motorsports Adds
BTR dual spring kit, Ti retainers
Forged rods, 6.125"
Forged pistons 4.030 bore
Forged crank 3.622"
BTR cam
BTR Gen II Rockerarm trunion kit
LS HD timing chain
LS HV oil pump
FLEX fuel tune

Current Build List
Holley HP ECU
Holley 3.5" LCD Touch Screen
Holley 7" digital Dash
Holley Fuel Pressure Reg
Derale Dual Fans
15X12 Drag Lites with E/T Streets
15X4 drag Lites W/ Micky Sportsman S
9 inch 4.10 spool
Fuel cell Holly sending unit
Cal Trac bars
Wilwood brakes
"Built" 4L80e (not sure what's been done too it, does have a transbreak)
REVMAX Billet 3200 stall converter
Forward Manual Valve Body
Holley High Ram Manifold
S475 Borg 75/88 Turbo
Holley Boost controller with CO2 Tank
317 Heads
8.50 cert rollcage with door bars
Corbeau Seats with RCI 5 point harness
Trans Cooler W/ Fan
Push/Pull Battery Disconnect
VS Blow off and Gates

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[OBS94]

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[OBS94]

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[Wh4t3v3rs]

nice rod!!! can't wait to see it with the new upgrades, should be a BEAST!!

 

[OBS94]

nice rod!!! can't wait to see it with the new upgrades, should be a BEAST!!

Thanks Man!
Well see, got to say I'm a little nervous about the trans. The guy I got this truck from claimed the engine was built as well but It was SBE when Mayhem got it pulled a part.

 

[Wh4t3v3rs]

I have small street build going on as well, and I was originally going to use the 4l80e. This is what I can tell you. If it has a trans brake, then it is more them likely built for 800+hp. The trans brake parts alone are $700 and takes lots of grinding and customizing to install. SOOO, if they took the time to do that, then you can probably assume its built fairly well! IMO

 

[OBS94]

I have small street build going on as well, and I was originally going to use the 4l80e. This is what I can tell you. If it has a trans brake, then it is more them likely built for 800+hp. The trans brake parts alone are $700 and takes lots of grinding and customizing to install. SOOO, if they took the time to do that, then you can probably assume its built fairly well! IMO

Good Luck on the build man!

I was thinking the same thing when I bought it. When it comes to buying stuff like this second hand, never really know what you got until you start pulling it apart. I bought this truck with a valve train tick hoping I could slap some new springs in it and be ready to roll. New springs fixed the tick but once we got the truck up to operating temp it developed a knock.........broke her down turns out it had 3 damaged rods and damage to the crank .

So I said **** it, lets make sure that doesn't happen again lol.

 

[Wh4t3v3rs]

Thank you sir!
Ya, you never know where someone drew that financial line or ran out of money. From the looks of the build, and the choice parts, I bet your pretty safe for what you're trying to do....

 

[OBS94]

We will find out end of August/ beginning of September.

 

[OBS94]

Once I get my truck back I'm going to have it painted. Need Some opinions on color.

My top choices right now are Gloss Black, Frost white or Cobalt Blue.

Let me know what you guys think.

I've really had my eye on a cobalt blue.

You must be registered for see images attach