You must be registered for see images attach
You must be registered for see images attach
got my new wheels in, and new tires mounted up
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
new CPP booster and master cylinder
You must be registered for see images attach
full lift
You must be registered for see images attach
new cpp booster/master cylinder installed
You must be registered for see images attach
aluminum overflow can installed
You must be registered for see images attach
You must be registered for see images attach
new bags to replace the pos airlift dominator air bags
You must be registered for see images attach
shaved door handle actuators
You must be registered for see images attach
ordered me my new steering wheel
You must be registered for see images attach
picked me up a new/used motor... supposed to be a 2004 5.3 vortec motor with 93k miles out of a rolled over/wrecked Tahoe
You must be registered for see images attach
dbw gas pedal assembly
You must be registered for see images attach
the engine harness and ecu that needs to be modified
You must be registered for see images attach
getting it slowly taken apart
You must be registered for see images attach
new steering wheel came in, and got it installed
You must be registered for see images attach
current pic of engine bay
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
framing up a rear floor
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
that fitment. lol
You must be registered for see images attach
another floor crossmember/frame piece... and welded in, with a few moree braces added to it
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
got a bunch more frame welding from top side done... ready to start covering it up
You must be registered for see images attach
sheet metal for the burb floor
You must be registered for see images attach
first piece cut to cover the floor
You must be registered for see images attach
second piece cut, and welding both in
You must be registered for see images attach
these two pieces are done... enough for now
You must be registered for see images attach
one of the wheel tubs trimmed/cut down and welded in, and working on another piece of the floor
You must be registered for see images attach
more sheet metal for the floor
You must be registered for see images attach
little set back... wasn't happy with the rear part of the floor, so i cut it back out to redo it cause it was warped and wavy
You must be registered for see images attach
doing it in 3 smaller pieces, and welding slower to keep the heat down and not to warp it
You must be registered for see images attach
left side piece tack welded in, now i need to trim the center piece a little bit and get it welded in
You must be registered for see images attach
all tack welded in... now just a butt load more until its welded solid
You must be registered for see images attach
Working on getting the left rear wheel tub installed
You must be registered for see images attach
Put some primer and satin black paint over the top side of the floor a little bit ago... bottom side of each piece was painted prior to being welded in
You must be registered for see images attach
Finally, after 3 weeks my PB dropmember LSx engine mounts came... Via the electric UPS truck. lol
You must be registered for see images attach
Working on the front upright part of the floor...
You must be registered for see images attach
Almost done welding in the front top floor pieces
You must be registered for see images attach
And painted...
You must be registered for see images attach
Picked up this seat today for $40 to use as the new rear seat in the suburban.... now at least they will both match. and some day they will get reupholstered
You must be registered for see images attach
First test fit and to see how its gonna look. may cut the seat bracket down like i did with the front one later on down the road, but not right now
You must be registered for see images attach
You must be registered for see images attach
Bolts welded to all 4 corners of the rear seat bracket.... now to just drill 4 mounting holes and get it bolted in.
You must be registered for see images attach