Help figuring out steering play.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
I have been trying to figure out the steering play in my 94 K1500 and a click when turning the wheel. I jacked up the truck and wiggled both tires left to right and there is tons of play. I've added some videos of the idler and pitman arms as well as the steering shaft and of the actual wheel moving back and forth. Can you guys help me out to see if anything looks off to you? This is my first K1500, so I'm unfamiliar if any of this is normal for these trucks. Thanks again.

xc_hide_links_from_guests_guests_error_hide_media

xc_hide_links_from_guests_guests_error_hide_media

xc_hide_links_from_guests_guests_error_hide_media

xc_hide_links_from_guests_guests_error_hide_media
 

east302

I'm Awesome
Joined
Oct 4, 2013
Messages
3,597
Reaction score
3,611
Location
Jackson, MS
No, none of that looks normal. That’s got to be a bear to drive.

It’s hard to judge unless you can watch the entire steering linkage move (looking to see where the movement stops). But best guess and part cannon approach is that the idler, idler bracket, pitman arm and tie rod ends could be replaced and make a nice improvement.

I’d also check the four ball joints for movement.

On the steering shaft, pull the collar back where the shaft connects to the steering gear and watch that rag joint when you turn the wheel.
 

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
Should I also look at the steering gear? And how would I check it? I've mainly owned rack and pinion vehicles. I'll check everything when I get home today.
 

east302

I'm Awesome
Joined
Oct 4, 2013
Messages
3,597
Reaction score
3,611
Location
Jackson, MS
It could also be worn, but it can be difficult to source a quality reman. Normally, you’d turn the steering wheel and see how quickly the pitman arm responds/turns. But since you have all of that play in the steering shaft it may be hard to gauge.

A possible workaround - You could try disconnecting the steering shaft and fitting a 12-pt socket and breaker bar onto the input shaft at the gearbox. Turn it back and forth and see how much slack is between it and the pitman arm.
 

alignman88

I'm Awesome
Joined
Aug 28, 2020
Messages
245
Reaction score
807
Location
St. Louis
Doing the “dry park” method like you did is great for tie rod end checking but they weren’t visible in the video. Any lateral play (side to side) that doesn’t match spindle is bad. Be careful about condemning the idler arm, they are deigned to be checked with one wheel raised, a dial indicator placed on it, and no more than 15lbs of hand pressure. I can’t remember if allowance of movement is .015 or 0.30. The steering arm geometry on GM trucks is odd, so they have the play built into the idler to make up for lack of Ackerman at tight turns. Hence the light tire squealing in tight turns-outside tire still dragging a little.
 

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
Doing the “dry park” method like you did is great for tie rod end checking but they weren’t visible in the video. Any lateral play (side to side) that doesn’t match spindle is bad. Be careful about condemning the idler arm, they are deigned to be checked with one wheel raised, a dial indicator placed on it, and no more than 15lbs of hand pressure. I can’t remember if allowance of movement is .015 or 0.30. The steering arm geometry on GM trucks is odd, so they have the play built into the idler to make up for lack of Ackerman at tight turns. Hence the light tire squealing in tight turns-outside tire still dragging a little.
I have to clarify. The first video of the wheel moving back and forth. It is actually jacked up just enough for the tire to not make contact with the pavement. I turned the steering wheel with both wheels on the ground today and tons of movement in the steering box before it even begins to turn the wheels. So I'm guessing I need to either rebuild the steering box or buy another. Is rebuilding one something the average shade tree mechanic can accomplish? I'm also concerned about the popping and movement in the steering shaft going into the firewall. You can feel an hear a click. Is there something in the column that needs replaced?
 

east302

I'm Awesome
Joined
Oct 4, 2013
Messages
3,597
Reaction score
3,611
Location
Jackson, MS
Was that slack in the steering gear observed with the steering shaft in place?
Meaning - any play at the pitman arm could be a result of whatever you have going on in the shaft.

Parts store reman gearboxes are a crap shoot. Bluetop and Redhead tend to get good reviews, though. I’ve had both, no issues.

I don’t remember if it’s in the manual, but check to see if the rebuild procedure is there. PDF downloads are here for most 88-98 models.


YouTube may be another source for Saginaw box rebuilds. With the correct tools and a good manual, I don’t see why you couldn’t do the job yourself.
 

cgreppi

Newbie
Joined
Mar 22, 2014
Messages
3
Reaction score
13
Get a Red Top Steering Gear. They have a tag on it that says " this steering gear has Zero Play".And it is TRUE. I have a 1990 K1500 Replaced steering gear, ball joints, idler arm, pitman arm, inner & outer tie rods and the hub w/ bearings. I went from sober drunk driving, to ZERO PLAY.
 

454cid

Sooper Pooper
Supporting Member
Joined
Sep 5, 2010
Messages
10,526
Reaction score
15,299
Location
The 26th State

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
Was that slack in the steering gear observed with the steering shaft in place?
Meaning - any play at the pitman arm could be a result of whatever you have going on in the shaft.

Parts store reman gearboxes are a crap shoot. Bluetop and Redhead tend to get good reviews, though. I’ve had both, no issues.

I don’t remember if it’s in the manual, but check to see if the rebuild procedure is there. PDF downloads are here for most 88-98 models.


YouTube may be another source for Saginaw box rebuilds. With the correct tools and a good manual, I don’t see why you couldn’t do the job yourself.
Yes the steering shaft was connected. I watched the steering box and my dad moved the steering wheel back and forth and tons of play in the steering wheel before any movement was seen in steering box or pitman arm.
 

east302

I'm Awesome
Joined
Oct 4, 2013
Messages
3,597
Reaction score
3,611
Location
Jackson, MS
Just to rule out the influence of any play in the steering shaft and rag joint, I’d disconnect the steering shaft and compare by turning the input shaft on the steering gear. You might need a longer ratchet/breaker bar or something for leverage. Careful with the splines on the gearbox, don’t damage them.
 

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
Here is the amount of play I have in the steering box.
xc_hide_links_from_guests_guests_error_hide_media
 

mr_josh

OBS Enthusiast
Joined
Mar 12, 2020
Messages
81
Reaction score
153
Location
Oregon
It’s hard to show the amount of input to output play in a mounted box but basically any real play you can discern with your hands is going to be problematic.

Might be time to sit down with the credit card and plan a front end rebuild. I put a Redhead + a new rag joint on my truck about 6,500 miles ago and while it feels great, it has developed a bit of leak. Your mileage may vary.
 

jedi_jackson

Newbie
Joined
Jul 15, 2021
Messages
25
Reaction score
12
Location
Virginia
It’s hard to show the amount of input to output play in a mounted box but basically any real play you can discern with your hands is going to be problematic.

Might be time to sit down with the credit card and plan a front end rebuild. I put a Redhead + a new rag joint on my truck about 6,500 miles ago and while it feels great, it has developed a bit of leak. Your mileage may vary.
Bummer about the redhead. That's the one I was looking to get. I actually found some adjustments you can do to the steering boxes. So I did that and got maybe a small amount out. Going to rebuild the rest of the steering and then go from there.
 

Medic0893

Newbie
Joined
Nov 3, 2019
Messages
45
Reaction score
52
Location
Philadelphia
Allot of great advice here, word of caution… pick a piece or 2 and see how you do. Replacing everything at the same time could lead to unnecessary replacement. No doubt it needs quite a bit of TLC but do it in stages. Steering box is so last. Suspension parts and rag joint first. Jeep has a mid-shaft that replaces the rag joint, I highly recommend that. Good luck.
 

Justin2500

Newbie
Joined
Aug 26, 2021
Messages
7
Reaction score
6
Location
Ohio
I had a similar situation with the c2500 I just bought. Do the cheap stuff and obvious stuff first.

I replaced all tie rod ends pitman arm, idler and idler bracket. I used all moog for those. Then I had a small leak in my gear box and just replaced the pitman shaft seal on the gear box. It’s like a new truck. Not too much $$ either. I inspected my rag joint and it looked ok. Might do the jeep mod someday anyway.
Good luck!!
 

Skeeters65

Newbie
Joined
Aug 24, 2021
Messages
12
Reaction score
8
Location
CT
Allot of great advice here, word of caution… pick a piece or 2 and see how you do. Replacing everything at the same time could lead to unnecessary replacement. No doubt it needs quite a bit of TLC but do it in stages. Steering box is so last. Suspension parts and rag joint first. Jeep has a mid-shaft that replaces the rag joint, I highly recommend that. Good luck.
I did the Jeep steering shaft to get rid of the old worn rag joint and it got rid of 90% of my steering play!!
 

Staff online

Forum statistics

Threads
78,085
Messages
1,644,805
Members
81,215
Latest member
wesco1974
Top