454 TBI Sensors Function Location

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
The question is:
“Sensors where are all of them located on the engine, and what do they do and why?”

1990 454 ss TBI
 

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
The what and why may be similar, but please share your knowledge if you would.

My knowledge about computer controlled vehicles is very basic and elementary.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,614
Reaction score
29,654
Location
Tonopah, AZ

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
I appreciate the link very much, however like me my phone is to old and or doesn’t have the capability to open it up. Again another area of technology I’m am very deficient in.
 

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
Maybe I can make it simpler for me to understand.

These are the sensors I know of.
1) MAP
2) IAC
3) COOLANT TEMP
4) KNOCK SENSOR
5) OXEGYN
6) TPS
7) VSS

Did I miss anything? Or add one it doesn’t have?

Thanks to any and all again for the help.
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,614
Reaction score
29,654
Location
Tonopah, AZ
EGR valve - on intake manifold passenger side of Throttle Body
Oil pressure switch for fuel pump - On rear china rail near distributor
Oil pressure sensor for gauges - Driver's side of block next to oil filter
CTS for gauges - between cylinders 1 & 3 on driver's side head

I'm not sure on a 454 where they all are but on a SBC ...
1) MAP - on intake manifold passenger side of Throttle Body
2) IAC - passenger side of TB
3) COOLANT TEMP - next to T-Stat housing
4) KNOCK SENSOR - just above the starter
5) OXEGYN - Driver's side in the exhaust manifold
6) TPS - Passenger side of TB in line with the throttle shaft
7) VSS - tail housing of trans
 

PlayingWithTBI

2022 Truck of the Year
Supporting Member
Joined
Jan 3, 2019
Messages
14,614
Reaction score
29,654
Location
Tonopah, AZ
I forgot ESC module - on intake manifold passenger side in front of EGR module.

Edit: if you have the A.I.R. (Air Injection Reaction or Smog Pump) the valve is mounted on it with a vacuum line from the TB going to it.
 
Last edited:

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,632
Reaction score
27,277
Location
The Seasonally Frozen Wastelands
The question is:
“Sensors where are all of them located on the engine, and what do they do and why?”

1990 454 ss TBI

These are the sensors I know of.
1) MAP
2) IAC
3) COOLANT TEMP
4) KNOCK SENSOR
5) OXEGYN
6) TPS
7) VSS
I suggest a thorough reading of the service manual for your vehicle. This is best done via paper copies; but scans for select models and years are available on this site. I've bought most of my paper copies from eBay. I do have a couple on DVD; less satisfactory but readily available and not expensive at ~$50.

For the record, the computer receives information from sensors, processes that info based on it's programming, and commands other devices which could be called "outputs". Number 2 in your list--IAC--is an output, not a sensor. Same with EGR solenoid, AIR diverter solenoid, fuel pump relay, the variable-timing section of the ignition module, and fuel injectors.

A sensor that hasn't been mentioned is the ignition pickup coil, (RPM) the signal is delivered to the computer indirectly, via the ignition module. The computer also has a voltage reference, delivered through one of the fuses. From a certain perspective, that fuse is a "sensor" of voltage.

In all cases--sensors and outputs--the associated wire harness is integral to the operation of the system. A failure in the wire harness is often mistaken for a failure of the associated sensor or output
 

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
Just to explain my all of the sudden curiosity.

My 1990 454ss truck recently started stalling when put in gear. It would die immediately. If you feathered the gas pedal it would stay running.

A very smart buddy of mine insisted it was the IAC I replaced it and it made no difference.

I consulted another guy who was a gm mechanic when these trucks were on the dealer lots.

He said if I replaced the map sensor he was positive that would fix it since the IAC didn’t.

They both are extremely knowledgeable when it comes to computer controlled vehicles and they both ALWAYS give me a hard time because all of my hot rods street rods and street race cars all have carburetors.

However neither part/sensor mentioned was the problem.

At that point I was on my own neither one had anymore advice and insisted one or both new parts were bad/junk.

One said he thought the computer was bad.. “That’s really the only thing left it could be.”

So I went back to basics that I apply to all my carbureted engines.

It was the distributor... The magnetic pick up was shot and was wore out.

Got a new distributor from the parts store and 30 minutes later problem was solved.

When I told them what it was

They both said hmmm we’ll good, glad you got it fixed.

I appreciate everyone’s help but I don’t understand 1/2 of what you guys were talking about.

The truck runs fine now. Eventually it will get a carb too.

Im afraid it’s something I’m not smart enough to comprehend at least without taking a certified training course ha ha!!

Thank you all very much for all your input and advice!
 
Last edited:

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,632
Reaction score
27,277
Location
The Seasonally Frozen Wastelands
A very smart buddy of mine insisted it was the IAC I replaced it and it made no difference.

I consulted another guy who was a gm mechanic when these trucks were on the dealer lots.

He said if I replaced the map sensor he was positive that would fix it since the IAC didn’t.

They both are extremely knowledgeable when it comes to computer controlled vehicles
No, they aren't. They're guessers and parts-changers. Connecting a scan tool, and ten minutes later you'd have seen that the RPM signal was goofy. You wouldn't have been tricked into thinking the IAC and MAP were the cause.

Eventually it will get a carb too.
Almost certainly a mistake. At least your trans isn't computer-controlled.
 

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
Well... one of them did connect a snap on brand scan tool and the computer did not communicate with the scan tool.

Thats why the second buddy told me he thought the computer was bad.

I wish I knew more about how and what it did when he hooked it up but then again that’s my lack of knowledge showing through again.

Thanks again I appreciate your input.

You sound like my first buddy. He says carburetors are controlled vacuum leaks.

I’m going to build a afr headed 496 similar to the one I built for my 94 k3500.

I understand what you are saying from a efficiency and longevity point of view.

These trucks aren’t daily drivers (just toys) for me and I’m more concerned with performance and simplicity than fuel economy and efficiency. But I do understand your point of view and don’t disagree.
 

Attachments

  • C7B8A4FA-6BC3-42C1-B820-21BC2D64A2E0.jpeg
    C7B8A4FA-6BC3-42C1-B820-21BC2D64A2E0.jpeg
    232.8 KB · Views: 5
  • 20061A67-4849-4068-827F-88901D8F9CC7.jpeg
    20061A67-4849-4068-827F-88901D8F9CC7.jpeg
    283.4 KB · Views: 5
Last edited:

Erik the Awful

Truly Awesome
Air Force Supporting Member
Joined
Aug 9, 2019
Messages
10,038
Reaction score
23,543
Location
Choctaw, OK
You sound like my first buddy. He says carburetors are controlled vacuum leaks.
...and fuel injection is just a computer-controlled spray bottle.

If anyone tells you they know what the problem is without troubleshooting, they're just parts changers. I can recommend and say, "there's a good chance it's blah, blah, blah part", but it's very rare that I can nail it down to one part with confidence.
 

BigDaddy72

OBS Enthusiast
Joined
Jun 14, 2021
Messages
51
Reaction score
58
Location
Arkansas
I’ve made a lot of power with carbs and built some dead reliable daily drivers with carbs.

But I won’t argue witch one is more efficient.

I try to respect everyone’s opinion and find valve in all point of view even if I don’t agree.

Thanks again to all for the comments.
 

Staff online

Forum statistics

Threads
78,078
Messages
1,644,655
Members
81,191
Latest member
2000Jimmy
Top