manual

  1. R

    93 k1500 manual swap

    I’ve been wanting to manual swap my 93 k1500 and I found a wrecked truck here a while back, same year and everything, only difference is it is a manual. Would I be able to pull all the necessary parts off of the donor truck and be able to do the swap with minimal cost (providing all the parts...
  2. L

    transmission grinding hard

    I have a 1995 K1500 with the 5.7 engine and 5 speed manual transmission. I bought with around 170,000 miles, drove it about 10,000 miles, and now all gears are grinding when i try to put it in. It takes about 4 tries to even get it into 4th gear at this point, and it grinds LOUD every time. It...
  3. A

    Making an external slave work with a Ls?

    Over the past few months I’ve been swapping an lq9 into my 95. Finally got to where I thought I was really close just to bolt up the trans and have the slave cylinder interfere with the oil pan. So now I’m at a crossroads, either swap in a 96+ nv3500, convert mine to internal, or go to a t56...
  4. Brantly

    Pilot Bearing Orientation

    I have a 98 1500 with the nv3500 and its been awhile since ive replaced the clutch including the pilot bearing, i was wondering whoch side of the bearing goes towards the engine? there doesnt seem to be a taper on either end thanks guys.
  5. Sprocket454ss

    clutch not disengaging (lm7 + hm290)

    My clutch is not disengaging when I press the pedal in. I did the nfw1050 flywheel and luke 4-201 clutch kit. I can row through all the gears when the truck is sitting still, pressing in the clutch helps a little bit with this. If I fire it up in first gear with the clutch pressed in (I may be...
  6. Tommy Frantz

    Clutch question 1991 1500

    Guys, what are my clutch options for a 1991 1500 4x4? I swapped all this into a Jeep and the clutch pedal forces are very high, even for the hydraulic clutch. I have a 12" stock clutch and pressure plate in there now,, is there a lower spring pressure plate available for this setup? I've been...
    • Tommy Frantz
    • Thread
    • clutch force hdyraulic manual pedal plate pressure transmission
    • Replies: 9
    • Forum: Transmissions
  7. A

    Need some pointers on SAS

    What's up everyone? I have a 1994 GMC Sierra SLE 6.5L N/A 4 speed with granny low ext cab short wheel base. Currently it's still running IFS and I would like to go Solid Axle. What kit do y'all recommend? I want to use the axles, t case and steering components if possible from a 70s or 80s 3/4...
  8. A

    97 C1500 350 manual, enjoy

  9. KaidenP2

    95 C1500 bench to 99 Suburban 60/40 power help

    Hi guys! I have a 95 c1500 rcsb with the manual bench seat (Absolutely sucks!) Anyway... I have a whole suburban here and I have all the bolts and what not lined up for it. It's 6 way I believe with no lumbar support driver side is 60 portion. My question is in terms of getting the power to...
  10. E

    Nv3500 swap trouble

    I’ve got an nv3500 from a 91 c1500 2wD. I am currently undergoing a motor and auto to manual swap in my 1988 c1500. After putting in the transmission it slid in with no problem. After further inspection I was able to move the fork all the way back and all the way forward with no resistance. The...
    • El Gibbay
    • Thread
    • 5lm60 c1500 manual manual swap nv3500 problem solution
    • Replies: 3
    • Forum: Transmissions
  11. Tommy Frantz

    97 K3500 automatic to manual transmission

    Guys, I'm converting my 97 K3500 from an automatic to a manual transmission and I have a question about how the interlock for the ignition works. When you tried to turn the key to LOCK there used to be a little lever that you'd depress to be able to do this. This function kept you from turning...
  12. Thatguy0909

    Need Help Clutch Line Blowing Off

    I just replaced my whole clutch system due to my slave cylinder going out, now I cant get the clutch line to stay in the slave cylinder under pressure. Its a 1997 k1500 with the nv3500 in it. The slave cylinder has the metal clip but it also came with the plastic lock collar. Do I need to make...
  13. CarolinaChevyDad

    Help! My 7.4 idles low and stalls in neutral - manual trans

    Its a 99 K3500 with the factory NV4500 trans (4x4 obviously) that I just bought a week ago. It drove great the first 600 miles and towed my car home on a trailer from a few states away where I bought it. Just this weekend, it started dropping to 350-500rpm when I would push in the clutch or put...

Latest posts

Staff online

Members online

... and 14 more.
Total: 1,769 (members: 64, guests: 1,705)

Forum statistics

Threads
64,344
Messages
1,391,808
Members
51,464
Latest member
gurtomoreno

Share this page

Top