Search results

  1. N

    NV4500 bellhousing

    i have a 93 k1500 with a NV3500 that lost a countershaft bearing. I was going to buy a reman from smart parts auto but the NV4500 is only a few hundred more but I cannot find a bellhousing to mount this transmission to my 350. Anybody ever buy a new bellhousing or have any suggestions? These...
  2. N

    Trailmaster lift kits

    Did some searching and couldn't find too much information on trailmaster lift kits. Just bought a 93 with a 4" trailmaster lift on 34x10.50 TSLs. Are these lifts still around and is anybody running one here? And the only difference between a 4 and 6" kit would be taller blocks and tbar crank...
  3. N

    Crank And 1.5 Inch Blocks!

    2" blocks and crank on 285/75s. rear is about half a inch taller then the front is
  4. N

    What's the best starter option?

    battery is a few months old, and the starter does have a heat shield over the solenoid. Ignition system is in good shape, no more the half a volt of voltage drop on power and ground side. Never had any problems until I replaced the starter. Im going to try and find a junkyard oem chevy gear...
  5. N

    What's the best starter option?

    I've warrantied my reman napa starter now 2 times in a year and a half, I need to buy something more reliable. Anybody have good or bad experiences with the NBS gear reduction from a 4.3 or a summit racing gear reduction? Or should I just buy a new ac delco starter?
  6. N

    96+ steering shafts

    Dorman part number is 31002. It's not listed as fitting the truck but the rubber is the same size
  7. N

    96+ steering shafts

    i found a disc thats close enough to the factory size to modify a little and use. Ill try to get some pics tonight or tomorrow. thanks for all the input, been rushing because im moving to PA next week for school.
  8. N

    96+ steering shafts

    I think I'm gonna try to drill 4 new holes on the same disc, have a junkyard lower shaft in the vice now and the holes for the rivets are what wore out. The holes are stretched. I'm gonna drill new holes in the old disc and use bigger bolts and tighten it up with a impact and see where it goes...
  9. N

    96+ steering shafts

    Has anybody just replaced the rubber in the joint? Dorman makes a help kit, I think the part number is like 31005 or around there but the disc is about twice the size then the one in my 97. I can't find any other parts locally
  10. N

    96+ steering shafts

    Would this be the same as a NBS pickup truck? I had a NBS bottom end in my hand to day at the pick a part but I figured it wouldn't fit my top because it had a much wider tube the the factory lower shaft.
  11. N

    steering shaft from a work van?

    I just posted a similar question. From what I've read, I don't think 97 and 98 can swap in any shaft because those years have speed sensitive steering. My rag joint is shot and I can't find parts anywhere to fix it.
  12. N

    96+ steering shafts

    So what do you do when you need to replace the rag joint? I can't find any parts stores with one that will fit, and I've looked in a few junkyards but all the shafts I found had the same play as mine. I have a 97 with the speed sensitive crap.
  13. N

    96+ steering shafts

    I've been searching for weeks about these rag joints in the steering shafts. Mines shot, and I can't find a kit anywhere with the right size disc to repair mine, and there really isn't any information about what to do on 96+ trucks. Anybody fixed or modified theirs to the jeep style like the...
  14. N

    Starter Shims/Noisy Start

  15. N

    Starter Shims/Noisy Start

    I have a 97 K1500 ECSB with the 5.7 and 4L60E. This past June, the trans went out with 220,000 on it so I had it rebuilt. While it was out I did a rear main and bought a new flexplate. I replaced the starter a month later because the old one was packed full of mud and dirt. I did not use the...
  16. N

    GMT400 You can't quit looking at!

  17. N

    Frame and Wheel Well Paint

    What kind of paint do you guys use on your frame and wheel wells? I've tried flat black krylon spray paint and rubber undercoating and they both get trashed by mud. they dont clean up and it looks like crap. any suggestions on a paint to use? or some kind of clear coat to easily wash mud off? thanks
  18. N

    New Tires

    some short term goals is to get the transmission in, and once i recover from that some 2" blocks to level the truck and a new exhaust, probably flowmaster 44s or 10s. It takes awhile to save upfor stuff making minimum wage haha. Eventually I want to completely restore the truck with 14FF rear...
  19. N

    New Tires

    Got rid of my little 245/75s and got these 285/75 Definity M/Ts..Don't really know how they handle in mud yet though, got sick and tired of my transmission acting up and pulled it yesterday, and its going to the shop tomorrow.Ive also added the cab lights and the brush guard in the last few...
  20. N

    answer to any 4l60e trouble

    I just installed the transgo 4L60E kit to fix my P1870 code, as well as the corvette shift servo. after i did this, the truck wont shift out of first gear without letting my foot off the gas and reverse is very delayed. after 4 days of driving like this the shift servo on the side of the...
  21. N

    P1870 Code

    I know there's multiple threads about the P1870 code but I need some more clarification. I have a 97 K1500 ecsb with the 5.7 and 4L60E and its starting to shift very hard between 1 and 2. the second time it happened it gave the code P1870. From my research its a sleeve in the valve body that's...
  22. N

    IFS Trouble

    If im gonna spend thousands on a SAS id just go with one tons...there was a military cucv for sale around here about a month ago..37 inch military tires, dana 60 up front and 14 FF in the rear with 4.56s and a locker stock. I think id buy one of those and then sell the rest of the truck and my...
  23. N

    IFS Trouble

    I beat on that thing so hard I thought my ring gear was gonna come through the diff housing. I couldnt get it out at all. The lock ring on the shaft is just stuck I guess. I threw it all back together and put the axle back in the next day, but the seals bad and now I cant ever regear if I cant...
  24. N

    IFS Trouble

    Heres some pictures
  25. N

    IFS Trouble

    Can somebody please explain the proper way to remove the axle shafts? I'm replacing the inner seals, and have been fighting with this axle for hours. I have the entire axle out and the passenger side shaft out, but the drivers side (directly on the case) won't move. I've been using a slide...

Latest posts

Staff online

Members online

... and 28 more.
Total: 1,842 (members: 78, guests: 1,764)

Forum statistics

Threads
64,646
Messages
1,397,866
Members
52,139
Latest member
sea1351

Share this page

Top