Interrupt the starter wire with a normally open push button. Hide it somewhere within reach of the driver seat. Button must be pressed while the key is in the start position or no power goes to the starter.
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Thanks. To clarify, you mean the power wire going to the starter which is of thicker gauge, or the signal wire that goes to the starter?Interrupt the starter wire with a normally open push button. Hide it somewhere within reach of the driver seat. Button must be pressed while the key is in the start position or no power goes to the starter.
Install the button on the signal wire that goes to the solenoidThanks. To clarify, you mean the power wire going to the starter which is of thicker gauge, or the signal wire that goes to the starter?
Ok, makes sense since the thick wire comes from the battery, whereas the signal wire is in the dash.Install the button on the signal wire that goes to the solenoid
Thanks. To clarify, you mean the power wire going to the starter which is of thicker gauge, or the signal wire that goes to the starter?
What he said.Install the button on the signal wire that goes to the solenoid
Interrupt the starter wire with a normally open push button. Hide it somewhere within reach of the driver seat. Button must be pressed while the key is in the start position or no power goes to the starter.
Amazing, I like this approach. Great write-up.Hello aj_08,
618 Syndicate has the best idea. Using the following wiring diagram from the
Factory Service Manual, let's see what would be the best way to implement
the 'denial of starter usage' function while you are away from your vehicle:
You must be registered for see images attach
Alright, when it comes to a relay, we can either disable it's functioning (the control side)
-or- we can allow the relay to function but interrupt the power to the load that the relay
is controlling.
To keep this short enough that it will actually be read, when you look at the circuit above,
the RED and PPL (purple) wires would be your target if you decided to interrupt the actual
current being sent to the starter solenoid. (NOTE: Note that both of these wire colors are
marked as a '3' in metric wire diameter. If you check out the attached conversion table
this translates to '12 gauge' wire that is commonly used by sparky types.)
Instead, my recommendation would be to interrupt the control side of the starter solenoid.
This way, instead of the 'momentary on' switch having to reliably carry amps of current, instead
we'll task it with making/breaking the milliamps of current required to operate the solenoid.
In addition, the RED & PPL wires are physically run between the Underhood Fuse Block and the
starter solenoid, so having to route this 12 gauge wire from the Underhood fuse block to a
switch reachable from the driver position is more work. And the shorter that a 'high current'
circuit is, the better.
**** How to test kill switch functionality prior to implementation ****
First, locate the Ignition Switch on the diagram. Notice that the switch must be turned by
the human all the way to the Start position. If you follow the wire from the Start terminal,
it then goes through the CRANK fuse. (#8 in the IP {Instrument Panel} fuse block.)
Pull that fuse, and verify that the starter is now disabled when you attempt to start your
K1500. Note that the wire feeding the fuse is yellow, and after the fuse it is a 18 or 20 gauge
purple wire. (Remember it's a lower current control signal for the relay.)
At this point, once you've proven to yourself that you can actually disable the starter with
the CRANK fuse, now you know where to wire the switch you choose in series in this circuit.
And if your truck is an automatic, I think that this is the best overall way to implement the
'denial of starter' to a thief. To further thwart a thief if your vehicle is a stick (and can be
the engine can be pop started via the clutch) then I'd implement a switch to interrupt the
power to the fuel pump. (And since there's no pressurized fuel accumulator, unlike a carb
with local storage {fuel bowl(s)} a fuel injected truck won't run for more than a handful
of seconds at most before stalling out.)
****
The nice about all of the above is that you can prove/disprove this approach in a minute
or so for no parts cost.
And I typed in the above because anyone trying to make it harder to for idiots to steal
their GMT400 shares my outlook on life. The less nonsense in life the better.
Good on your for deciding to implement a kill switch. Do your best to make the switch
as counterintuitive as possible. (!)
Hope the above gives you a better understanding of what's involved in getting your
starter spinning.
Cheers -
Ah i understand what your saying too,Yes, I see what you are saying. Good thing about the fuel shutting off mid drive is the truck will stop. Thieves may just ditch it there. With the spark, if the switch does fail the truck isn't going anywhere, in addition, there is always current running in that switch and is a higher risk for problems. A starter switch draws power once for every start and does not need to be on after it starts which is less risky I believe.