350 gets close to stalling when stopping

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
It doesn’t happen every time I stop, but occasionally the rpms drop <500. It’s on my 1994 k1500 with a 5.7. I don’t have any issues with my idle after startup or once up to temp. This occurs when coming to a stop sign at ~30 mph. I push the clutch all the way in and shift to neutral when coming to a stop to try and avoid the issue and it still happens. The only thing I have done with the ignition system is replace the idle air control valve since I got it. Any idea on where to start the parts cannon? Or is this an easy fix?

I scrolled through the stupid engine questions thread and didn’t see anything like my issue.
 

thegawd

I'm Done!
Joined
Feb 29, 2020
Messages
2,260
Reaction score
4,297
Location
The Country Formerly Known as Canada!
check for a leaky vacume brake booster.... it leaks more when the brakes are pressed.... the computer tries to compensate and then the truck falls on its face or stalls when you let off and give it the gas. when its leaking really bad you will hear a hissing noise and you will basically have unassisted brakes. I think all these old brake boosters are at the end of there life.

Al
 
Last edited:

alpinecrick

I'm Awesome
Joined
Jun 12, 2015
Messages
1,694
Reaction score
1,839
Location
Western Slope of Colorado
It doesn’t happen every time I stop, but occasionally the rpms drop <500. It’s on my 1994 k1500 with a 5.7. I don’t have any issues with my idle after startup or once up to temp. This occurs when coming to a stop sign at ~30 mph. I push the clutch all the way in and shift to neutral when coming to a stop to try and avoid the issue and it still happens. The only thing I have done with the ignition system is replace the idle air control valve since I got it. Any idea on where to start the parts cannon? Or is this an easy fix?

I scrolled through the stupid engine questions thread and didn’t see anything like my issue.
Can you put a scanner on it and see what your idle rpms actually are? Does this happen when coming to stop. Does it do it going down the road and putting the clutch in and letting it idle?
What brand of IAC?
 

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
Can you put a scanner on it and see what your idle rpms actually are? Does this happen when coming to stop. Does it do it going down the road and putting the clutch in and letting it idle?
What brand of IAC?
It’s a 1994 so my obd2 scanner won’t work. It only happens when using both brake and clutch at same time. It’s a AC Delco IAC. I will check for vacuum leaks tomorrow it does have a bad hiss that sounds almost like a beep.
 

96TahoeDoug

I'm Awesome
Joined
Apr 13, 2021
Messages
181
Reaction score
226
Location
South Mountain Phx
No messing around change the fuel filter I did mine at 96k with onset of idle symptoms it was butt plugged black slip pouring out, more idle misses at 98k change again last night, purrssss real nice. $7.99 AutoZone cheapest. Statistics wise I can't believe people change them at all let alone 30k and it's rare I see it as a first case must do but it is a must do.
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,650
Reaction score
27,334
Location
The Seasonally Frozen Wastelands
Yes to pretty-much all of the above; but as usual I favor connecting a scan tool and looking at the data stream.

Find out if the IAC is actually being commanded properly; can the scan tool raise and lower the idle speed? What is commanded idle speed vs. actual idle speed? Does the O2 sensor reading make sense? MAP sensor reading? RPM signal?

Wouldn't hurt to verify fuel pressure, look at the spray of fuel coming out of the injectors. Connect a timing light, verify initial timing and that it advances when you plug the connector back in.
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,650
Reaction score
27,334
Location
The Seasonally Frozen Wastelands
It only happens when using both brake and clutch at same time... ...it does have a bad hiss that sounds almost like a beep.
Does it only hiss/beep when you push the brake pedal? Is it coming from the power booster or the booster plumbing? Or do you hear it in the cab?
 

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
No messing around change the fuel filter I did mine at 96k with onset of idle symptoms it was butt plugged black slip pouring out, more idle misses at 98k change again last night, purrssss real nice. $7.99 AutoZone cheapest. Statistics wise I can't believe people change them at all let alone 30k and it's rare I see it as a first case must do but it is a must do.
I already have a AC delco fuel filter and will swap it in the morning. Thank you for your insight.
 

Schurkey

For a pacifist, I sure am a radical mother...
Supporting Member
Joined
Jan 14, 2018
Messages
17,650
Reaction score
27,334
Location
The Seasonally Frozen Wastelands
I have seen that your go to is always a scan tool. Which one do you recommend?

I bought a Snap-On MTG2500. The MT2500 is more common, and less expensive on eBay. Mind you, this tool was ancient when I bought it in 2004-ish. I keep telling myself I should upgrade to something newer, but I don't actually do it. My software cartridges work from '80 1/2 to 2006 for domestic vehicles.

If I were buying a tool tomorrow, I'd be looking at buying something used in the the Snap-On "Solus" family--Solus, Solus Pro, Solus Ultra, Solus Edge. They may have another newer one now--I've kinda lost track. There's hundreds, maybe thousands of Solus scan tools and accessories on eBay.

In addition to the tool, you want to have software installed on it new enough for any vehicle you plan to use it on. The newest vehicle I own is a 2003; so software that goes to '06 works fine for me...so far.

You'd also need adapter cables to suit whatever you plan to work on. There's the very-common "OBD II" connector, plus a large number of adapter "keys"; but the older, "OBD I" stuff has a different connector for each brand of car, and some brands have more than one. GM alone has three OBD I connectors, but only two are popular.

The OTC Genysis and Pegysis tools are competitive with Snappy; the GM dealerships use Tech 2 tools which are enormously expensive and hard-to-find, so naturally the Communists are counterfeiting them by the thousands and selling online. I've used the prehistoric OTC Monitor 2000 and Monitor 4000, but the Snap-On '2500 series made those obsolete in the 1980s.

There's also computer-software "scan tools" you could load onto a laptop, and then buy the vehicle harness adapter separately.

There's low-budget "consumer-grade" tools available online or from local parts stores. Many of them are crappy "code readers", not actual scan tools. And some of the ones that do give you access to the data stream, only talk to the engine computer, but not ABS, transmission, air bags, instrument cluster, etc. the way a professional-grade tool would. When it was my money, I bought an older, used "professional-grade" tool, rather than a brand-new "consumer-grade" tool.
 

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
I bought a Snap-On MTG2500. The MT2500 is more common, and less expensive on eBay. Mind you, this tool was ancient when I bought it in 2004-ish. I keep telling myself I should upgrade to something newer, but I don't actually do it. My software cartridges work from '80 1/2 to 2006 for domestic vehicles.

If I were buying a tool tomorrow, I'd be looking at buying something used in the the Snap-On "Solus" family--Solus, Solus Pro, Solus Ultra, Solus Edge. They may have another newer one now--I've kinda lost track. There's hundreds, maybe thousands of Solus scan tools and accessories on eBay.

In addition to the tool, you want to have software installed on it new enough for any vehicle you plan to use it on. The newest vehicle I own is a 2003; so software that goes to '06 works fine for me...so far.

You'd also need adapter cables to suit whatever you plan to work on. There's the very-common "OBD II" connector, plus a large number of adapter "keys"; but the older, "OBD I" stuff has a different connector for each brand of car, and some brands have more than one. GM alone has three OBD I connectors, but only two are popular.

The OTC Genysis and Pegysis tools are competitive with Snappy; the GM dealerships use Tech 2 tools which are enormously expensive and hard-to-find, so naturally the Communists are counterfeiting them by the thousands and selling online. I've used the prehistoric OTC Monitor 2000 and Monitor 4000, but the Snap-On '2500 series made those obsolete in the 1980s.

There's also computer-software "scan tools" you could load onto a laptop, and then buy the vehicle harness adapter separately.

There's low-budget "consumer-grade" tools available online or from local parts stores. Many of them are crappy "code readers", not actual scan tools. And some of the ones that do give you access to the data stream, only talk to the engine computer, but not ABS, transmission, air bags, instrument cluster, etc. the way a professional-grade tool would. When it was my money, I bought an older, used "professional-grade" tool, rather than a brand-new "consumer-grade" tool.
Thank you for you amazing and detailed reply. After hours of research and a lack of sleep I am stuck between a actron cp9690 for $200 or a MT2500 with the domestic cards and Asian imports cards up to 1999 with adapters for ~$275. I understand that “the brick” is bidirectional which is a big win. I just can’t seem to pull the trigger knowing that the actron would basically be plug and play. It looks like the MT2500 would be the best to go with for OBD0 and OBD1.

Is there a reason the actron would be a bad buy for the wider model year coverage? What are the added benefits of having the snap on and bidirectional?

The Solus is a bit out of my shade tree hobby budget unfortunately.I am new to working on older trucks, but after this one I would like to get another.
 

man-a-fre

still voiding warranties
Joined
Jun 5, 2019
Messages
374
Reaction score
483
Location
Lincoln Ne
I would go with the actron or bosch one over the mt2500 ,it will do newer cars also and no cartridges or keys to put in I have both the Actron and the mt2500 , go with the Actron it shows the same datastream readings the mt2500 does and works great for our trucks.My mt2500 has the 9.2 version programmable black cartriges so it goes to like 08 or so and I have the can 1b adapter. The actron I use most often it automatically recognizes the year and make so you dont have to put the vin in like you do on the mt2500.
 
Last edited:

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
how did you test the brake booster? if you hear a hiss when pressing the brakes it is absolutely leaking into the cab.

so I'm a bit confused. what else could makea hissing noise when pressing the brakes. I can't think of anything.

Al
The hiss is always there not just when braking. After running the vehicle and pressing the brakes I can remove the vacuum booster check valve and it still has vacuum. If there’s a vacuum leak it is before it goes in the booster. I can also completely remove the check valve from the vacuum line and plug it and get the same beep/hiss. The check valve is still one way and the grommet is solid.
 

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
perfect! I was just curuous as on an obd2 you can read the fuel trims but I wanted to know how to do it without a scanner.

sounds like you know more than I do.

when you choose a scanner can you post the link? I'm interested in picking up a more professional one as well.
All I know I have learned on YouTube videos. I bet you know far more than I do I am still new to these trucks.

As far as the OBD1 scan tool I think both would be a good option for me, but I want to wait for a response from Schurkey. I’m kind of leaning towards the snap on, but it has to be worth the extra $75. The cartridges and accessories aren’t cheap if I need to buy more in the future.
 

Nilocsemliw

Newbie
Joined
Jun 6, 2021
Messages
15
Reaction score
31
Location
Oregon
perfect! I was just curuous as on an obd2 you can read the fuel trims but I wanted to know how to do it without a scanner.

sounds like you know more than I do.

when you choose a scanner can you post the link? I'm interested in picking up a more professional one as well.
It could always still be the brake booster but that is not the source of the vacuum leak. When pressing the brakes the buzz does not change.
 

Latest posts

Members online

Forum statistics

Threads
78,111
Messages
1,645,206
Members
81,289
Latest member
Kikkomania
Top