Search results

  1. S

    tbi open/closed loop issues

    Installed carquest p/n CX13077 3 wire o2 sensor in the manifold, unplugged the down stream o2 and ran the harness to the other side of the trans and plugged right up. on a side note, I checked continuity between the first single wire to the ECM and no go. Did the same with the down stream, and...
  2. S

    tbi open/closed loop issues

    Nobody has anything to chime in with?
  3. S

    tbi open/closed loop issues

    Man it seems like its been forever since I've made a post on here, but now is the time to throw it to the elders and see what they think on the matter. I'm working on the 92 in my sig, and recently blew the little v6. After working the living piss out of that engine, and pushing it to its...
  4. S

    92 tbi 4.3 drivability issues

    No body?
  5. S

    92 tbi 4.3 drivability issues

    Ran a fuel pressure test. 13 psi I didn't suspect fuel pressure problems, especially with the fouled plugs, but figured i could atleast rule it out
  6. S

    92 tbi 4.3 drivability issues

    I did find (what i beleive to be) a faulty ground on the intake last night... All conections to that point showed a couple ohms resistance vs. 0 resistance at any givin ground point on the engine. I changed the ground point from the intake to the A/C bracket all ground wires now ohm to 0 No change
  7. S

    92 tbi 4.3 drivability issues

    alright, my truck has been acting up lately, and now its to the point that i cant drive it. The symptoms really have me stumped.the problem is intermittent, and does not really have ryhme or reason, however the condition seems to "like to" start at cruising/steady throttle. Took of from a stop...
  8. S

    my 92 aka "CLIFFORD"

    Not a whole lot to report, I've been working for a local farmer/rancher for little or nothing (way below minimum wage, but it pays the bills for now) I bought a used 4.3 in Enid, Oklahoma and then tore my PCL riding a bull on September 1st... So I put the engine in my truck with a torn PCL by...
  9. S

    radio quality

    Btw i forgot to add, its a sony xplod (i forget what model)... the ground makes a little sence, the small ground wire from the battery terminal to the fender broke at the eyelit sometime last yr.
  10. S

    radio quality

    So would it be worth picking up an oem antenna cable?
  11. S

    radio quality

    I have an aftermarket radio in my 92, have had for a while. Still running the oem antenna tho. Radio quality has never been all that much to brag about, however the truck has always been in areas with decent station reception. Now that im in the middle of BFE in the new mexico desert. The lack...
  12. S

    fan temp switch

    Finally found what i was looking for... P/n AR34... Heres a link just for anybody else that is as picky as i am http://m.summitracing.com/parts/rfw-ar34
  13. S

    fan temp switch

    I never knew those yrs even ran electic fans... Awsome, i will do some lookin into that!
  14. S

    fan temp switch

    Think i might have found a possible match for what im looking for... Temp switch for a 98 jeep grnd cherokee 5.9L... However, that part seems to have been discontinued since 2008. Its hard to find specs for temp range on it since its not available in the after market
  15. S

    fan temp switch

    So im looking for a part, that so far seems to be IMPOSSIBLE to find. Ive found a few leads, but end up with a dead end. Im looking at installing a set of dual ford taurus fans on my 92. Pricing out wiring kits, and its unbeleiveable what they whant for a decent kit! Hell ill just get what i...
  16. S

    nv3500

    nobody?
  17. S

    nv3500

    according to research, they're only able to handle up to 300ftlbs of tq. im currently building and swapping my v6 for a used .020 350w/ 217 heads... factory numbers on the 350 is 210hp/300ftlbs and im considering upgrading the cam which would improve those numbers. eventually i do plan...
  18. S

    my 92 aka "CLIFFORD"

    finally was able to get into the engine, and its worse than i anticipated on the flip side, i did find out somebody has been through the engine not too long ago... .020 over pistons
  19. S

    my 92 aka "CLIFFORD"

    now some previews of the near future the engine has been sitting in the back yard for about 4 years, so i didnt have high hopes for a simple swap, looks like im gna have to completely go thru it one of my next mods: 98 ford taurus duals :gr_grin:
  20. S

    my 92 aka "CLIFFORD"

    didnt take many of the rod knock repair, but did get these loaded up about to leave god forsaken Craig, CO
  21. S

    my 92 aka "CLIFFORD"

    Pit up a sheet for a wind block to help keel the snow out of the engine bay By time i was done, i couldnt feel my fingers or feet
  22. S

    my 92 aka "CLIFFORD"

  23. S

    my 92 aka "CLIFFORD"

    heres some of the valve repair
  24. S

    my 92 aka "CLIFFORD"

    heres some of the truck pics first for those that havnt seen it
  25. S

    my 92 aka "CLIFFORD"

    Few updates... truck still ran and drove (just ran like , had little power, drank gas like a semi) and i had to finish a house remodel in a town 20 miles out so i was driving the truck still for about 2-3mo... Finally after thnxgvng i was able to work on it, an a compression test on the...

Latest posts

Staff online

Members online

... and 13 more.
Total: 1,827 (members: 63, guests: 1,764)

Forum statistics

Threads
64,386
Messages
1,392,742
Members
51,540
Latest member
RLJohnson

Share this page

Top