Recent content by seth9199

97 chevy to make transmission shift with carb

hey guys im trying to do a build out of a 97 chevy and i need to figure out how to make the trans shift. with the original pcm. i know i need a rpm and a trottle pos signal but dont know what wires from the harness i need to put into the rpm rear out swaping in a carb and a double roller so ckp...
- seth9199
- Thread
- Mar 7, 2022
- carburetor shifting problems transmission control
- Replies: 0
- Forum: Engine Performance + Maintenance
poor acceleration

So it seems like its either getting too much fuel or not enough after pushing it i lock into first when it starts acting up and rev up and itll act normal again. Could a sensor cause the engine to not work right at temperature? Or after working hard. Or even the spider injectors?
- seth9199
- Post #14
- Jun 2, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

Yup one to one oem. How ever when i unplug maf the issue goes away. So im thinking it may just be the downstream 02s
- seth9199
- Post #10
- May 22, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

Replaced the maf all already. Imma try the foulers then if not ill unplug amd see if it continues
- seth9199
- Post #8
- May 21, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

if it was a clogged cat wouldnt that mean id have the issue all the time?
- seth9199
- Post #6
- May 21, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

yeah all looks good. i do get running lean codes when it happens. but even when it happens have same fuel pressure as i do when it dosent happen. about 63 psi. is there a possibility it could be o2 sensors?. the codes also go away under basic driving for bout 25 miles. im almost thinking run...
- seth9199
- Post #5
- May 21, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

Update fuel pressure while driving is good even when it boggs driving. So at this point im clueless
- seth9199
- Post #2
- May 20, 2020
- Forum: 96+ Vortec Performance + Computer Swaps
poor acceleration

so recently I've been experiencing a problem wit my 97 k2500 5,7 vortec. Whenever i accelerate hard and get up to speed one or two times or push the truck. i start to have a super slow acceleration issue like its bogging down almost but it still seems to downshift with the lack of power. it...
- seth9199
- Thread
- May 20, 2020
- Replies: 13
- Forum: 96+ Vortec Performance + Computer Swaps
Can the dash be swapped

So I've got a 97 k2500 with no air bags and im wondering if i could install the 95-96 dash board in the truck so that cubby is gone and id have that flat tray design.
- seth9199
- Thread
- Apr 12, 2020
- Replies: 3
- Forum: OEM and Custom Interiors
Bed cross member replacement.

Yeah just noticed they just added that to there line up
- seth9199
- Post #10
- Mar 25, 2020
- Forum: Paint / Body / Detailing
Bed cross member replacement.

Hey thanks yeah im not planning on the project till summer. So that works out.i wasent sure if it was like the dodge where they used a different one for short and long beds
- seth9199
- Post #7
- Feb 26, 2020
- Forum: Paint / Body / Detailing
Bed cross member replacement.

How much did the shop charge you for those?
- seth9199
- Post #6
- Feb 26, 2020
- Forum: Paint / Body / Detailing
Bed cross member replacement.

i figured i would have an extra just wanted to make sure it would mount up ok
- seth9199
- Post #3
- Feb 13, 2020
- Forum: Paint / Body / Detailing
Bed cross member replacement.

So i want to replace the bet supports on my short bed but i cant find a short bed kit. However i found a kit for the long bed so what im wondering is would that kit work for a short bed?. Or would the mounts be different? 926-984 is the dorman part number.
- seth9199
- Thread
- Feb 11, 2020
- Replies: 10
- Forum: Paint / Body / Detailing
Different ohms

Yeah the truck were the only ones without an external amp
- seth9199
- Post #24
- Dec 16, 2019
- Forum: Audio + Electronics