Search results

  1. seth9199

    97 chevy to make transmission shift with carb

    hey guys im trying to do a build out of a 97 chevy and i need to figure out how to make the trans shift. with the original pcm. i know i need a rpm and a trottle pos signal but dont know what wires from the harness i need to put into the rpm rear out swaping in a carb and a double roller so ckp...
  2. seth9199

    poor acceleration

    So it seems like its either getting too much fuel or not enough after pushing it i lock into first when it starts acting up and rev up and itll act normal again. Could a sensor cause the engine to not work right at temperature? Or after working hard. Or even the spider injectors?
  3. seth9199

    poor acceleration

    Yup one to one oem. How ever when i unplug maf the issue goes away. So im thinking it may just be the downstream 02s
  4. seth9199

    poor acceleration

    Replaced the maf all already. Imma try the foulers then if not ill unplug amd see if it continues
  5. seth9199

    poor acceleration

    if it was a clogged cat wouldnt that mean id have the issue all the time?
  6. seth9199

    poor acceleration

    yeah all looks good. i do get running lean codes when it happens. but even when it happens have same fuel pressure as i do when it dosent happen. about 63 psi. is there a possibility it could be o2 sensors?. the codes also go away under basic driving for bout 25 miles. im almost thinking run...
  7. seth9199

    poor acceleration

    Update fuel pressure while driving is good even when it boggs driving. So at this point im clueless
  8. seth9199

    poor acceleration

    so recently I've been experiencing a problem wit my 97 k2500 5,7 vortec. Whenever i accelerate hard and get up to speed one or two times or push the truck. i start to have a super slow acceleration issue like its bogging down almost but it still seems to downshift with the lack of power. it...
  9. seth9199

    Can the dash be swapped

    So I've got a 97 k2500 with no air bags and im wondering if i could install the 95-96 dash board in the truck so that cubby is gone and id have that flat tray design.
  10. seth9199

    Bed cross member replacement.

    Yeah just noticed they just added that to there line up
  11. seth9199

    Bed cross member replacement.

    Hey thanks yeah im not planning on the project till summer. So that works out.i wasent sure if it was like the dodge where they used a different one for short and long beds
  12. seth9199

    Bed cross member replacement.

    How much did the shop charge you for those?
  13. seth9199

    Bed cross member replacement.

    i figured i would have an extra just wanted to make sure it would mount up ok
  14. seth9199

    Bed cross member replacement.

    So i want to replace the bet supports on my short bed but i cant find a short bed kit. However i found a kit for the long bed so what im wondering is would that kit work for a short bed?. Or would the mounts be different? 926-984 is the dorman part number.
  15. seth9199

    Different ohms

    Yeah the truck were the only ones without an external amp
  16. seth9199

    Different ohms

    Or what if i added resisters to the lines?
  17. seth9199

    Different ohms

    So if i put an after market amp after the stock head unit would that help to correct?
  18. seth9199

    Different ohms

    So what im getting from this is i should be fine and its gonna be more bass and loud
  19. seth9199

    Different ohms

    My dad used to have a truck just like it as a kid so more or less memory sake
  20. seth9199

    Different ohms

    Does anyone know the wattage output of the stock head unit because i got "factory upgrade" speakers and there not high wattage or anything but they are higher than stock. Like 35w front and 75w rear or sum like that
  21. seth9199

    Different ohms

    So the factory speakers in my 97 k2500 im pretty sure are 10 ohm speakers. However the set i want to install are 4 ohm. What can i expect? Are they going to be louder or quieter? Is there going to be distortion? Or should i install an amp. Also stock head unit. Factory came with the premium...
  22. seth9199

    k2500 8600gvrw trucks tow ratings have gotta be under rated

    im pretty sure 7500lbs is more like 1500 numbers these trucks should be able to tow 10,000lbs easy. so my question is whats holding them back from pulling more?
  23. seth9199

    Bed liner rocker panels/rust proofing

    yeah Ill post them when i get home it came out really nice and matches the body style very well
  24. seth9199

    Towing capability

    Yep it was
  25. seth9199

    Towing capability

    All the same execpt tbi vs vortec

Latest posts

Members online

Total: 1,020 (members: 15, guests: 1,005)

Forum statistics

Threads
64,352
Messages
1,391,931
Members
51,472
Latest member
Jake rogers

Share this page

Top