Search results

  1. D

    long crank

    I’m having the same issue on my 98 350 replaced spark plugs and wires, cap and rotor, ignition coil, and icm. My fuel pressure is at 60 with key on and 53-54 while running. It doesn’t hesitate at all runs good just the long crank time with door on gas pedal is where I’m stuck.
  2. D

    P1351

    Yes I have it on the truck right now. I just cant understand why with two different brand new ones it will throw a high voltage code but with the OEM one it has no codes. I heard a fuel pump can do this I did a fuel pressure test and with key on it’s at 60 and with engine running it’s at...
  3. D

    P1351

    Need help I replaced on my 98 c1500 spark plug and wires, distributor cap and rotor, ignition coil, and ignition control module. Well I put a delphi ICM and the p1351 code pops up so I put the original oem one back on and the p1351 goes away. I returned the new icm and bought a different one...
  4. D

    98 c1500 5.7

    No it’s runs fine doesn’t skip a beat.
  5. D

    98 c1500 5.7

    I let it prime for about 5 seconds but I still have to give it a little gas on warm starts to get it going.
  6. D

    98 c1500 5.7

    hey guys sorry if this has been asked before. I have a 98 c1500 350 5.7 and is it normal for this year engine to have to press gas pedal to start? on cold starts it will start up fine by itself without pushing gas but on a warm it cranks until I give it gas most of the time. when driving it does...
  7. D

    Tired hit inner fender on bumps! HELP!!!

    Ahhh ok I’ll try that tomorrow thanks
  8. D

    Tired hit inner fender on bumps! HELP!!!

    Wait sorry I had put the jack on the frame and took the wheel off and tried and nothing should I put load on the under arm to adjust???
  9. D

    Tired hit inner fender on bumps! HELP!!!

    On the frame but I will try this thanks
  10. D

    Tired hit inner fender on bumps! HELP!!!

    Alright just finish installing the coilovers. Instructions said to install on lowest setting so I did that now the damn thing is too low so I jacked it up took off the wheel and tried to adjust ring but g damn that thing is hard to turn with the spanned wrench. So I gave up for today.. anyone...
  11. D

    Tired hit inner fender on bumps! HELP!!!

    Sorry I haven’t replied I put on some bigger bump stops off the rear of my buddys gmc it don’t rub unless I hit a really bad dip. So I let it sit but I recently ordered some coilovers and rear shocks with adjustable stiffener knobs. I will be installing today my only Q is I cannot find torque...
  12. D

    Tired hit inner fender on bumps! HELP!!!

    I would have to check but I bought some taller spring stiffeners hopefully this helps.
  13. D

    Tired hit inner fender on bumps! HELP!!!

    Only when I hit a dip or pothole I can see where it’s hitting on the inside of the top of the fender well
  14. D

    Tired hit inner fender on bumps! HELP!!!

    It’s at the very top it’s a 98 c1500 single cab 5.7L and the kit number from bell tech is 688ND
  15. D

    Tired hit inner fender on bumps! HELP!!!

    Hey guys new to forum here just got my truck with a bell tech 4/6 drop. Well I noticed rubbing on hard bumps so I trimmed the bump stops and now it’s even worse. I got Under the truck and saw that it was rubbing the fender well. The fenders are rolled so no issue there just hits on the top of...

Latest posts

Members online

... and 34 more.
Total: 1,928 (members: 84, guests: 1,844)

Forum statistics

Threads
64,510
Messages
1,395,543
Members
51,861
Latest member
dadlyf3

Share this page

Top