Search results

tpi conversion wiring harness

ok everybody im looking to see what my options are on my wiring to control my transmission and engine i have the tpi intake off of a 88 trans-am and a 4l60e transmission.i have checked with jims performance on getting my harness rebuilt into a dual ecm version and ive looked through books on how...
- chevyboy1992
- Thread
- Dec 9, 2011
- Replies: 4
- Forum: Engine Performance + Maintenance
heater hose help

ok guys ive got my engine all set up its the intake out of a 88 trans-am and idk how to run the heater hosesfor this intake. im just trying to figure out how to get them run.can somebody give me a little help please
- chevyboy1992
- Thread
- Dec 9, 2011
- Replies: 11
- Forum: Engine Performance + Maintenance
rocker arms

ok i as everybody knows im rebuilding my engine and i want to add a little more to it.ive done some looking and ive read that rocker arms can add a little power.i have 1.5 rocker arms that go to my heads i have now.what would 1.6s do for me? i have heard that the factory rocker arms vary between...
- chevyboy1992
- Thread
- Nov 30, 2011
- Replies: 0
- Forum: Engine Performance + Maintenance
valve covers

ok guys i am looking into buying new valve covers and the valve covers i have--have the ccv hole and the pcv valve hole and the oil cap hole but all the new ones im looking into only have the two holes no oil cap hole what do i need to do am i looking in the wrong direction
- chevyboy1992
- Thread
- Nov 30, 2011
- Replies: 15
- Forum: Engine Performance + Maintenance
cylinder head help

ok guys i have my stock 193 heads and i am most likely going to haev to run them with my new engine setup.so im looking at what people call (head work) or a (valve job) when they do this what are they actually doing? just changing valve stem seals?i have new comp cams keepers,retainers,springs...
- chevyboy1992
- Thread
- Nov 28, 2011
- Replies: 1
- Forum: Engine Performance + Maintenance
radiator

ok guys i am restoring my truck.i took out my old radiator and it was all banged up.im looking at new ones.i know one for my truck is 34'' wide.i found a 41'' wide would it fit?would it work
- chevyboy1992
- Thread
- Nov 26, 2011
- Replies: 0
- Forum: Engine Performance + Maintenance
chroming

ok guys i might be in the wrong area.i have a 95 z71 with a 350 in it i want to chrome alot of my parts like valve covers pulleys aluminum intake and alot more.and i dont know what route to take.ive heard of some good spray chrome companies and ive heard of good chroming companies that do it the...
- chevyboy1992
- Thread
- Nov 26, 2011
- Replies: 6
- Forum: Paint / Body / Detailing
brake line help

ok i have a 95 z71 ext. cab and i am restoring it.i removed my old brake lines and they had badly mashed areas and stressed areas so im looking to get or make new ones.i looked on the web at advance auto parts and they have rolls of brake line would that be a good idea or would i need to go to a...
- chevyboy1992
- Thread
- Nov 25, 2011
- Replies: 14
- Forum: Axles + Brakes
trans temp and pressure guages

i have a 95 z71 with a 4l60e trans. i want to install a transmission temperature guage and pressure guage.has this been done on this truck or is it possible?are they useless i am just trying to keep an eye on everything and keep it all maintained thanks for the help everybody
- chevyboy1992
- Thread
- Nov 24, 2011
- Replies: 5
- Forum: Transmissions
electric fan questions

ok guys i have 2 14'' electronic fans.and i am looking into everything i will need to run them.ive been researching and i found an adjustable thermostat controller.am i looking in the right direction? thanks for the help
- chevyboy1992
- Thread
- Nov 24, 2011
- Replies: 24
- Forum: Engine Performance + Maintenance
transfer case advice

ok guys i have a 95 z71 with a 4l60e thansmission and a np241 transfer case.i was told i could swap over to a 2500 t-case and idk what the np243 would do any better than my np241? any suggestions or opinions what would the 243 do for me???
- chevyboy1992
- Thread
- Nov 18, 2011
- Replies: 6
- Forum: Transfer Cases
rear brakes

ok guys i have a 95 z71 and i am restoring it at the moment and when i tore it all down i replaced my brake lines through the intire truck.i havent roughted the rear brake lines yet i was wondering if the rear brakes actually do anything in stopping power because when i put my new rear gears in...
- chevyboy1992
- Thread
- Nov 16, 2011
- Replies: 2
- Forum: Axles + Brakes
rebuilding my engine

ok guys i have a 95 z71 and im rebuilding my engine myself to learn how i have put in the bottom end already and torqued to spec. but i want to make sure i dont have to mic any thing for clearance its all new parts eagle crank i beam rods and .30 pistons will i have to mic for clearance between...
- chevyboy1992
- Thread
- Nov 7, 2011
- Replies: 24
- Forum: Engine Performance + Maintenance
intake problem

ok everybody i have a 95 chevy engine i rebuilt it and i bought a 88 trans am tpi intake.i tried to mount it up yesterday and the middle set of bolts are angled different to mount it to the heads.how do i get it mounted up?are the center bolts necessary ?
- chevyboy1992
- Thread
- Oct 27, 2011
- Replies: 35
- Forum: Engine Performance + Maintenance
little more lift

ok guys i have a 95 z71 with 10'' suspension 3'' body the truck sags in the front due to 200 pounds of steel i built the bumper out of.i was wondering if there was a way to lift the front maybe 3'' or so and it not have to be a tb turn. thanks
- chevyboy1992
- Thread
- Oct 20, 2011
- Replies: 9
- Forum: Stock Suspension + Bolt On Kits
herculiner idea

hey everybody im new on here.i have a 95 z71 13'' of lift and 38.5 thornbirds and i want to paint it with something very rugged and tough i saw where some had painted their entire truck in herculiner.what aresome opinions about this? thanks
- chevyboy1992
- Thread
- Oct 20, 2011
- Replies: 49
- Forum: Paint / Body / Detailing