El Tigre
I'm Awesome
Before using any rubber type cap. I'd install an appropriate size pipe plug coated w/RTV. Or,at the very least a rubber stopper,then the cap.
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
If the truck has a recently replaced radiator, it may have done what my recently acquired pickup has done. The internal transmission fluid pre heater/ cooler has been leaking ATF into the coolant. Made chocolate milk just like it does with motor oil. No telling how long it's been doing this. I've had it 3 weeks, and last week it started shifting funny, so I checked the transmission fluid. None on the stick, and no obvious leaking underneath. Around the same time, it peed orange on the ground; the clamp on the filler tank bottle hose was old and letting it seep. Fixing that yesterday led to the discovery where 3 quarts of MERCON V fluid went! So now I get to spend $350 on a radiator and hoses and more coolant and a transmission filter kit and fluid.....Same here - I have the same bypased saddle cooler on my C2500 - and no obvious explanation why it was done (coolant isn't leaking across it and while I haven't absolutely proven it doesn't leak externally, a rudimentary check showed no sign of it).
My concern is that I'm losing the pre-warming of the ATF (though coolant rad is cold until thermostat opens) and cooling (though how much cooling there is given quite high coolant temps is debatable). I live in a coldish climate so the pre-warming is more of a concern.
One difference I noticed is that your saddle cooler seems to have different fittings to mine. Mine are threaded (female NPT(?)).
There is another forum member who by-passed their saddle cooler as it was leaking. They aren't too worried about it!
If the truck has a recently replaced radiator, it may have done what my recently acquired pickup has done. The internal transmission fluid pre heater/ cooler has been leaking ATF into the coolant. Made chocolate milk just like it does with motor oil. No telling how long it's been doing this. I've had it 3 weeks, and last week it started shifting funny, so I checked the transmission fluid. None on the stick, and no obvious leaking underneath. Around the same time, it peed orange on the ground; the clamp on the filler tank bottle hose was old and letting it seep. Fixing that yesterday led to the discovery where 3 quarts of MERCON V fluid went! So now I get to spend $350 on a radiator and hoses and more coolant and a transmission filter kit and fluid.....
First, the rubber capped outlet on the radiator is for the HEATER, not used on many models.
The trans cooler fittings are the two below with the brass plugs.
I have had street and performance transmissions built by some of the best in the country and every single one suggest (highly) that the cooler in the radiator be bypassed and a efficient external cooler be installed.
The only time I have had a failure is when I left the internal radiator cooler inline for the supposed pre-heat on a truck that was built to live mostly at higher altitudes in the mountains.
What I see in picture a $20.00 e-bay/amazon cooler that is very inefficient and actually causes restriction.
The inline filter should be on the inlet to the cooler, and not the outlet. The purpose of a inline is to try and save the cooler from contamination in the case of a failure.
You say there is a temp sensor in the line, but where/how does the electric fan energize? Is there a seperate temp switch inline, does it come on with key on, or manually activated at the dash?
I have run Hayden Transmission coolers in street and high performance vehicles for years without added fan and rarely see transfluid temps over 190 degrees. Study a Hayden Cooler design compared to the one on your unit and you will see why they are more efficient.
I even use them on vehicles with hydra-boost setups!
Also if you are getting that high a temps, you may want to have your transmission checked by a professional as you may have something slipping internally! Improper converter lock-up possibly?
Yes I've wondered about this too. Guess part of it depends on how cold it is.How much pre-warming is there really though?
The coolant radiator doesn't see heat until the engine is warm enough for its thermostat to open. Meanwhile the ATF has been taken from the warming environs of its gearbox and circulated out in the cold and returned colder than when it left (especially if there is an additional tube/fin cooler).
Is there a definitive view on the efficacy of this supposed pre-warming?