Search results

  1. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Ok I think I finally found the problem. I put a new pigtail on the TSP and ran new wires to the ECM for the TPS. And so far it's running good and shifting smoother than it ever has
  2. A

    Radio resets when obd2 scanner is plugged in

    Nope still trying to figure it out
  3. A

    Radio resets when obd2 scanner is plugged in

    It's bidirectional. I've used on other GM's, Jeeps, and even a Volvo does not happen on any other vehicle. I've also tried just a code reader something. I don't remember what brand it is. It's from Harbor Freight.
  4. A

    Radio resets when obd2 scanner is plugged in

    Ok I have a 97 k3500 and every time I plug in my scanner and turn the key on the radio completely resets. I've never had this happen on any other vehicle I've use this scanner on. So I don't think it's the scanner. Is there something that connects the two besides the fuse box.
  5. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I believe OD because I give gas and it will pick up speed just really slow. If I put it in 3rd and it seems to be ok
  6. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I know it been awhile since I last posted. But you know life gets in the way. So I put a new pcm in it and got codes P0785, P0740, and tps code. The power wire for the transmission plug was already replaced from previous owner. So I put the old pcm back in and all but the tps code went away. It...
  7. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Sorry it took so long but u finally got the fuel pump in. The motor is running better now, but I think I'm having transmission issues. It shifts fine but occasionally if I step on it it just won't kick down. It picks up speed just not very fast.
  8. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Ok I finally got a chance to work on the truck. Replaced the switch wire on the the starter. It seems to run a little better so I decided to check the fuel pressure again while it's running at idle it was at about 46lbs. So question is that to low or about right. I can't seem to find a spec on it.
  9. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Ok update checking the wires on the starter the small wire pulled out of connector real easily. Now question where does that wire run to?
  10. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Ok I'll have to check that out. I was going to replace the battery wire to the starter anyway.
  11. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I've check the fuses multiple times. I was wondering if maybe the fusebox had corroded and not getting a good connection or if a relay is going bad.
  12. A

    Flagship One pcm

    I just received a like to some manuals I'm going to look at them after work today.
  13. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I didn't ohm it for ground. I didn't think 11.7v was bad for a 12v system. Not sure what the knock count is I'll have to check it when I get off work. But from power wire on the icm plug to ground on the battery was reading 11.7v with key on engine off
  14. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I went from the ground wire on the icm plug to the positive side of the battery to see if I had ground. Key on engine off. I have no idea how old the O2 sensors are. I don't want to spend the money to change it over,but I have to get the truck up and running soon and that is an option.
  15. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Ok thanks I'll have to check it out. I'm almost to the point of put a carburetor on it.
  16. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Yeah it's Harbour Freight this is the only this i could find on it is a YouTube video. https://www.google.com/url?sa=t&source=web&rct=j&url=https://m.youtube.com/watch%3Fv%3DkEqGMYe4phg&ved=2ahUKEwjduuDt-fT4AhW6g2oFHbz7A4sQtwJ6BAgjEAI&usg=AOvVaw1CQbBccT-Qtg0daNN2by3Q
  17. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    A earlier it would run for a minute or two just fine than die. When I went out to get more data it ran fine for about 5 minutes till I shut it but still stumble when giving it gas
  18. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    That is the numbers I'm pulling off the scanner. I double checked it before I posted. I could be reading something wrong I'm new to these kind of scanners
  19. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    SHRTFTB1S1 (%) O to 1.6 SHRTFTB1S2 N/A SHRTFTB2S1 (%) -1.6 to 1.6 SHRTFTB2S2 (%) 99.2g O2B1S1 (V) .060 TO 800g O2B1S2 (V) .170 TO .175 O2B2S1 (V) .120 TO815 O2SB2S1 (V) .070 I just pull this right now. It's idling fine I give it a little gas and it stumbles and back fires.the O2 numbers do not...
  20. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    A little black smoke off an on usually when it starts running rough. O2b1S1 165 to 800
  21. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    Now I'm getting a high voltage ignition control. That wasn't there earlier today
  22. A

    Flagship One pcm

    I was able to force codes pcm was reading the proper one's.
  23. A

    97 K3500 7.4l spitting, sputtering, backfires, and stalls

    I try to restarted bearly could keep it running. Let it cool down for an hour or so started ran rough than would run fine. Unplug it again ran good than would shut off that happen a couple of times
Top