Search results

  1. Joe Rack

    Internal Slave Cylinder Replacement Question

    This is the cylinder in the transmission.
  2. Joe Rack

    Internal Slave Cylinder Replacement Question

    I have a 1998 RCSB 5.0, 5 speed, 4x4. I pulled the engine for a rebuild and want to replace the slave cylinder. How do i disconnect the hydraulic line from the cylinder? I appreciate any advise! Thanks, Joe
  3. Joe Rack

    Front end rebuild kits K2500

    Thank you guys for the replies. i Will start at Rock auto.
  4. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    IT IS FIXED!!!! Spent today replacing the ignition cylinder, ignition harness, blower motor and blower motor resistor. Everything works! 4WD engages, Temperature controls work perfectly, no service engine soon light and no ABS light. Well worth the effort. I have to thank YOUTUBE, especially...
  5. Joe Rack

    Front end rebuild kits K2500

    My next project is to rebuild the front suspension on my 1998 K2500 with 146k miles. The steering is a little loose, and will be replacing (at least) ball joints, pitman arm and idler arm. I also want to level out the front end. While I'm at it, from your experience, what else would you...
  6. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    Gentlemen, Thank you for all of the advice and guidance! I gave up and took the truck to a local mechanic to diagnose the problem. I have no shame in that! I could not solve my two issues. One being the 4WD, and the other being, no power to the temperature control panel. Turns out, the ignition...
  7. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    Is this the 2 prong connector you are referring to? if so, with the ignition key on and shifter in 2Hi, the green or blue-ish wire had power, the other wire did not have power. I then moved the floor shifter to 4Hi and the results were the same.
  8. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    Well...I installed a new transfer case position sensor, but that did not solve the problem. Mechanically, the transfer case works fine. I tried to learn how to use a multimeter. Here is what I did and it may not be right, but I tried. As for power in: with the multimeter set at DC V, the center...
  9. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    I'm not great with electrical stuff, but I'll give it a go! Thank you for the advice! I will follow up.
  10. Joe Rack

    1998 Cheyenne K2500 4WD not engaging

    I bought a non-running truck a few months ago. Original engine was blown. Installed a rebuilt 5.7 engine a a couple days ago. The truck runs and drives well. I am working out a few kinks. One being the 4WD will not engage. This truck has the manual transfer case on the floor. I installed a new...
  11. Joe Rack

    New member with 1994 C1500 and 1998 K2500

    Thank you! I was lucky, I found the red one locally, in northern Illinois. The guy who owned it moved up here from Georgia and then parked the truck next to his garage. It sat there for more than 5 years. He was moving again and put it up for sale. It wasn't running when i bought it, but it was...
  12. Joe Rack

    New member with 1994 C1500 and 1998 K2500

    Here are a couple pictures of our trucks. The Red C1500 Silverado has 83K original miles, 5.0/auto. The White K2500 Cheyenne is my project, 5.7/auto has 146K miles. I bought it not running a few months ago. The engine was blown. Just installed a rebuilt 5.7 and took it on it's maiden voyage...

Latest posts

Members online

... and 14 more.
Total: 1,697 (members: 64, guests: 1,633)

Forum statistics

Threads
64,357
Messages
1,392,047
Members
51,480
Latest member
GMsoulmate

Share this page

Top