Recent content by loom383

  1. L

    Turn signal switch replacement

    Yea that is the switch. I was wondering if i do use that switch can I run a separate button for cruise control?
  2. L

    Turn signal switch replacement

    The flasher button on my 95 gmc sierra broke the other day. I picked up a steering column with a turn signal switch in it. The one in my truck has cruise control but the one i picked up does not. Is it possible to remove the flasher button and replace it with the one on my truck? or is it...
  3. L

    1995 GMC EX CAB ISSUE

    it was the ignition switch! thanks guys!
  4. L

    1995 GMC EX CAB ISSUE

    Fuses are all fine, check my obd1 codes and I got the following... 66-A/C pressure sensor circuit error(low pressure indicated) 67-A/C pressure sensor circuit error 81-Transmission 2-3 error 82-3X Crankshaft position sensor circuit error 83-TCC Solenoid circuit error Any help would be great!
  5. L

    1995 GMC EX CAB ISSUE

    My 95 Gmc Sierra Ex Cab K1500 is having an issue. This morning when I went to start my truck both my tach and speedometer did not move. Also my gear select indicator would not light up. To make matters worse the truck was shifting hard almost like it was stuck in 3rd gear. Any ideas what could...
  6. L

    95 gmc obd1 code 13

    greatly appreciated!
  7. L

    95 gmc obd1 code 13

    Ok thank you! Do you know where the 02 sensor plug runs? I am not sure if the guy before me cut it off or what but I can't find it anywhere!
  8. L

    95 gmc obd1 code 13

    Heres some pictures of my truck. Both manifolds have that kind plug in it. The other 3 pictures are of the passenger side where the two pipes from the manifolds meet. There is a plug there as well. Not sure if this is any help but I figured it couldn't hurt. Thanks again for any help!
  9. L

    95 gmc obd1 code 13

    Do you know where the plug for that sensor runs to then?
  10. L

    95 gmc obd1 code 13

    I have a single Blue wire that runs under the booster down to the exhaust that has been cut and capped. my exhaust goes down and meets on the passenger side(where the 2 pipes y together) and the 02 sensor is right before the cat. Would that blue wire be for my 02 sensor?
  11. L

    95 gmc obd1 code 13

    ok thanks!
  12. L

    95 gmc obd1 code 13

    how many wires should be going to my 02 sensor then? and any clue what colors? Thanks for any help!
  13. L

    95 gmc obd1 code 13

    weird, I have a blue wire that is clipped and capped off. Ill check to see if I can find a purple wire. Thanks!
  14. L

    95 gmc obd1 code 13

    After looking closely It seems like my truck does not have any o2 sensors. It appears that each manifold has plugs in it, and right before the cat there is a plug in the exhaust where the 02 sensor would go. It seems like there is no emission system on my truck. Is it possible to even pass...
  15. L

    95 gmc obd1 code 13

    Hello, I have a 95 gmc ext cab k1500 with a 5.7l 350. My check engine light will come on after driving(usually around 10-20 mins) and sometimes will shut back off. The code is reading as 13 Oxygen sensor circuit open or no activity. Where is the o2 sensor(s) located? and does this usually mean...
See more

Latest posts

Staff online

Members online

Total: 811 (members: 31, guests: 780)

Forum statistics

Threads
64,743
Messages
1,399,759
Members
52,348
Latest member
chuck12

Share this page

Top