Search results

  1. J

    what camshaft came stock in a 95 k1500 350 tbi.

    trying to figure out what cam came in those motors. ie. hydraulic roller, flat tappet etc. i need to figure out becuase im using a motor from a 95 k1500 in my 92 trans am motor swap and im going to be building a 383 and need to know what type of cam to buy or if i need to buy a hyrdraulic roller...
  2. J

    350 tbi to 350 carb swap

    what can i keep and what can i get rid of and what do i need to make this happen.
  3. J

    my beautiful beast :)

    1998 k1500 z71 ecss-stock motor-4l60e, 2800 stall converter, shift kit, vette servo-40x17x17 mud hawgs-dana44 solid axle conversion-true dual no cats thru 18 inch cherry bomb glasspacks-5:13 gears-170k miles on the body-85k on the motor-14k on the tranny 1998 k1500 z71 ecsb-stock...
  4. J

    4l60e

    what do u guys think about a 4l60e with a 2800 stall converter and a shift kit on a truck with 5.13 gears.
  5. J

    sig request please help

    heres a couple pics of my two z71's I need a sig made along with directions on how to add it to my posts on the forum
  6. J

    2x1998 ecsb's my family of legends

    finally got the pics up scroll down to see them. 1998 chevy k1500 z71 ecsb maroon stock 5.7l vortec, 4l60, 3.73 gears, 6in bds lift with 315/75r16 tires ...163,000 miles...shorty headers, magnaflow cat kit, had a flowmaster true dual super 44 exhaust now straight piped with turn down after...
  7. J

    fuel line leaking

    my fuel feed line is leaking right after where it goes from rubber to steel near the gas tank. where can get a new line for an extended cab short bed or 141.5 in wheel base. i checked every parts store and they gave me the wrong one every time for a single cab truck.
  8. J

    fuel line leaking

    my fuel line is leaking right at the spot on the sending line where it goes from a rubber hose from the tank to the steel line. is there a quick fix that can last a few weeks till i get up some money to get it fixed right?
  9. J

    rear end leak

    its leaking around the cover ive tried rtv and a actual gasket but it still leaks a little bit. wtf is the problem here.
  10. J

    1999-2000 ccsb's

    ive been looking into maybe getting one soon. can i see some of you guys' or other pics.
  11. J

    anyone have pics and a write up for a true cold air intake

    looking to actually run some piping and stuff for a true cold air intake not under the hood by the engine actually sucking hot air.
  12. J

    1998 k1500 z71 ecsb exhaust

    this is what i just got installed on my truck about a month ago. almost as loud as straight piped just sexier. hedman shortie headers magnaflow cats trual dual flowmaster super 44's 4x12 inch tips out the back at 45 degrees -will post a vid and pics soon
  13. J

    i really need some doors or lower panels

    all 3 of my doors have pretty horrible rust on the bottom edges. anyone know where i can get all 3 doors with no rust idgaf what color. im in manteo, nc right now but next week ill be back in baton rouge, la.
  14. J

    how much should it cost?

    how much should it cost on average to replace all ball joints and tie rods on my 98 k1500 z71? and how hard is it to do it myself.
  15. J

    you think it can handle it?

    so my father in law wants me to take a kubota tractor with a front end loader on it to jacksonville texas from northeast north carolina. i have a 5.7l 98 k1500 and 3.73 gears. never have any problems with engine or tranny. im just not sure how much it weighs. i do have a 20ft dual axle trailer...
  16. J

    98 k1500 5.7l vortec power steering pump

    im changing mine today.is there anything i might run into that i dont know about. got my pump and my pulley puller with all the tools i need. to remove the old pump. thanks.
  17. J

    bad rust damage on bottom of doors

    i have some pretty ugly rust damage on the bottom of my drivers side and pass. side and 3rd door. the panel behind my drivers door is fine. what i was wondering was do you guys think its cheaper to go to a salvage yard and pull some decent doors and then get them painted when i get my whole...
  18. J

    taking off lift kit and returning to stock suspension

    is it possible without major changes. where can i find a complete stock suspension kit or whatever i need. im thinkin about removing my lift kit in the near future and selling it not to mention gas prices are rediculous.
  19. J

    98 K1500 Z71

    98 K1500 Z71-5.7L VORTEC -6IN. BDS LIFT-16IN RIMS WITH 36 IN. PROCOMP XTREME M/T TIRES-TRUE DUAL EXHAUST 2 DYNOMAX SUPERTURBOS WITH 3 1/2 TIPS. http://www.gmt400.com/forum/attachment.php?attachmentid=2711&d=1297493554
  20. J

    How do you make those signature things that go along with your posts

    ANYBODY CAN HELP?
  21. J

    DRIVERS SIDE DOOR KEYHOLE FELL OUT INSIDE MY DOOR

    i tried to take the door panel off got to the black metal panel with the plastic on it and cant get much further than that becuase of my window and lock actuator is attached to it through the doors fram itself. is there like some special tools i need or should i take it to the dealership and how...
  22. J

    dual exhuast and engine light

    I GOT MY DUAL EXHAUST INSTALLED ON MY 98 K1500 Z71 IN EARLY MARCH AND I JUST GOT AROUND TO ASKING ON HERE. BUT IS THERE ANY WAY I CAN MAKE MY ENGINE LIGHT STAY OF BECUASE EVERY SINCE I GOT THE EXHAUST MY ENGINE LIGHT HAS BEEN ON SAYING THAT MY CATALYST IS INEFFICIENT. IS THERE SOME WAY TO FIX THAT.
  23. J

    from louisiana i got a stock 98 chevy k1500 z71, 6in bds lift

    i need some advice on what exhaust setup is the best for a deep rumble and not to raspy. for my 98 chevy silverado z71 5.7l vortec

Latest posts

Members online

Total: 1,475 (members: 31, guests: 1,444)

Forum statistics

Threads
64,413
Messages
1,393,463
Members
51,598
Latest member
Garstina

Share this page

Top