Recent content by WhiteUCF

  1. WhiteUCF

    400 vs newer

    My uncle had a 400 when my dad bought his new '04 800. The 800 was a great truck, my granddad uses it daily now. But seeing the two sitting side by side at lunch time on Sundays at my great granddad's house just felt odd. Even as a 12 year old, the 400 was cooler. It wasn't even old, it was just...
  2. WhiteUCF

    1994 K1500 ECSB "The G Wagon"

    Man, that truck is gorgeous!
  3. WhiteUCF

    Dealer life

    @GoToGuy I was pulling pads off of a 20k mile GTI. Nothing should break on something that looks brand new! $27/hr?! My whole life before VW was cars. My first small block was at 9 years old. Both of my parents drag raced. My granddads both had full caged nitrous cars in the 80's. I knew my way...
  4. WhiteUCF

    Dealer life

    My granddad has 50 year old Craftsman tools he uses on a daily basis. That's why I trusted them. Little did I realize the newer stuff was garbage. Now I'm experimenting with Eastwood, Tekton, Sunex, etc. I'm not turning wrenches for a living anymore but I still want the best affordable tools you...
  5. WhiteUCF

    Dealer life

    Man, I was dead set on using Kobalt and Craftsman tools until I broke a 3/8 ratchet on a caliper bolt. Snap-on guy showed up the same day and figured since he was there, I'd try a 1/4 on that caliper bolt. The 1/4 broke it loose. I gave up on Craftsman right then and there. Didn't realize that...
  6. WhiteUCF

    Dealer life

    I don't miss it one bit. I was at a small VW dealership and us techs sold more cars than the salesmen. It was a crap show. Then I went to an independent dealership and the other "mechanics" had issues with swapping single cam Honda engines or doing brake shoes. After knocking out a year of...
  7. WhiteUCF

    The "correct" way to remove leaf spring bushings.

    This was the only way I could ever get subframe bushings on my drift cars to come out. There's something about the nostalgia of the broke drift days that'll keep me burning bushings out whether I have a press or not.
  8. WhiteUCF

    Shaky Idle

    What I was trying to get at was more along the lines of the quality of fuel and oil that was used in the past. Most fleet vehicles don't get the tlc you're giving it. They're just maintained. Especially if it's just a run around vehicle. A clean top end doesn't necessarily have any bearing on...
  9. WhiteUCF

    Shaky Idle

    Deposits like that at 7k aren't exactly normal BUT could be in your case. Not knowing how the engine was treated and maintained in the past could be indicative of carbon deposits being burnt up since you've put the effort into making the truck happy with new parts. Taking into consideration the...
  10. WhiteUCF

    Hey, Everyone.

    Luckily, I can't fight. My nose is too big.. That thing was bought new by my uncle in '62. We got ahold of it and pulled it down to a bare shell. It stays at my granddad's since he has a proper garage, not mine where actual work gets done and sparks are thrown. It honestly scares me to drive...
  11. WhiteUCF

    who are the go to steering/suspension parts now?

    I've seen broken ball joints too many times from them being loose. On plenty of GM trucks and at the track. Never seen one shoot the nut off. That's why I posted it. Wasn't sure if that was something normal with Moog. Especially on these trucks. My initial presumption was that it was just a...
  12. WhiteUCF

    Hey, Everyone.

    It's a '98, same as my truck. Both have been kind of obtainable dream cars since I was a kid. My car has 145k so far. It won't go up much - I might've put 3 miles on it in the last year. It'll fall in beside my '62 and be a garage queen.
  13. WhiteUCF

    who are the go to steering/suspension parts now?

    Not having the nut tight would be the simple answer. Then again, over tight would stretch the threads and be just as much of a failure point when the suspension compresses while near full lock. Neither were the case. OD of the shank too narrow allowing excess movement in the spindle? Ball joint...
  14. WhiteUCF

    97 vortec 305 intermittent low power, poor mpg rough idle in park.

    You're welcome! If I can think of anything else tomorrow when my brain is actually working, I'll let ya know.
  15. WhiteUCF

    97 vortec 305 intermittent low power, poor mpg rough idle in park.

    There's a couple of ways to go about checking for vacuum leaks. A smoke machine or a can of carb cleaner. A smoke machine will fill the system with smoke and you'd hopefully be able to see where the smoke is coming from. The normal method is spraying carb cleaner at the vacuum lines while the...
See more

Latest posts

Staff online

Members online

... and 21 more.
Total: 1,949 (members: 71, guests: 1,878)

Forum statistics

Threads
64,379
Messages
1,392,550
Members
51,520
Latest member
RockyDog64

Share this page

Top