Recent content by LosDoritos

  1. L

    Sniper fuel line return

    ok yall believe it or not im still on this lol. my tranny shop has had the truck since late November doing a throttle bracket for it... the builder wanted to check over the truck to make sure the tranny didn't get smoked again and he found out that my bracket that holds the tv cable was flexing...
  2. L

    Sniper fuel line return

    I went and checked on the cable and it’s not too loose or anything so ima get ahold of the shop on Monday and ask ab the whole sniper setup and even thinking ab letting them have the truck to sort out the tranny so I won’t have to worry ab it while worrying ab the motor, one less thing to worry...
  3. L

    Sniper fuel line return

    It did run better, but I only drove it maybe 5 miles, tranny is 700r4 so it could be, I just gotta check it. The trans got less than 1000 miles on it as well, so fingers crossed. had to get it rebuilt right after the new motor, the only thing they did differently than stock rebuild is put a...
  4. L

    Sniper fuel line return

    So I ran that tune to the shop to put new gaskets and wires on otw back I did a baby ripper buuuuttt I think I lost 3rd gear, so ima check the cable to see if it’s loose or what, if my transmission is screwed then it’s still under warranty hopefully the shop will go thru with it, I haven’t...
  5. L

    Sniper fuel line return

    i didnt like how rough the graph was so i hit smooth all then saved the smooth version as a separate file to not lose the original, here is after the smooth, i would assume the graph would be better if it were smooth but i have no idea :)
  6. L

    Sniper fuel line return

    Alright so after some beers and alone time I got that timing table brought over, got some gaskets coming in and the thicker spark plug wires that is recommend for the sniper/hyperspark system, there were some numbers almost impossible to read but that’s just for the decimals, here’s what I got
  7. L

    Sniper fuel line return

    I’ll have to look up some videos for an example, just so I know what I’m listening for, right now I probably won’t be able to hear it cause of my header gasket but I’ll try out that table
  8. L

    Sniper fuel line return

    Sorry had a eventful weekend, I haven’t touched the truck in a while but I can put a data log overlay on the timing table and move it around yes, I still have been doing some digging ab this and i created a forum on gearhead efi as well...
  9. L

    Sniper fuel line return

    and I did some digging on this and it turns out the sniper doesn’t have a knock input and/or can’t read it
  10. L

    Sniper fuel line return

    So I checked this video out and made a base table with my numbers, but idk how this looks and I don’t want it to be stupid and mess something up so here it is
  11. L

    Sniper fuel line return

    It doesI can’t snap WOT or itll backfire, sometimes it’ll catch itself others it’ll die, and even easing into it will not “drop a gear to disappear” should I make that red area higher timing in a smaller area, I feel like even when I got wide open I’m still on the top right edge of the 0 deg boxes
  12. L

    Sniper fuel line return

    So I checked the wire for the knock sensor and it is not in the sniper so I’ll get that connected here soon but I was driving it at 18 degrees and noticed a difference but something still off so I pulled logs and the configuration and this is the timing table that the sniper made, now like I...
  13. L

    Sniper fuel line return

    What’s the knock sensor labled as in the logs, it’s not tied in with stock still is it?
  14. L

    Sniper fuel line return

    Before work I went and drove ab 20 miles and got some data logs, this is at the timing shown in the pic, it backfired when I tried to snap WOT but gradually opening let me get all the way open, def felt the timing could be raised. I then set the cranking timing down and raised idle started it...
  15. L

    Sniper fuel line return

    I’ll def keep an eye on all that I do run 93 octane in the motor cause that’s what the motor manual calls for, I’ll also play with the timing after a learning drive to see how that works is that your WOT timing? What are your timing values set at on the sniper screen, cranking was one that I...
See more

Latest posts

Staff online

Members online

... and 27 more.
Total: 1,701 (members: 77, guests: 1,624)

Forum statistics

Threads
64,527
Messages
1,395,952
Members
51,916
Latest member
nroberts84

Share this page

Top