Recent content by Javlin42

  1. J

    Lowering a 4x4

    I didn't know that
  2. J

    Lowering a 4x4

    So the gmt800 lca fits the factory gmt400 lca mounting location? Does it keep the same track width? Do you know if the uppers are compatible?
  3. J

    Lets see some dropped C1500s

    2/4 drop. F/R 15X8 255/60 5/8 drop. F: 17x8 225/65 R: 17x9.5 265/70 5/7 drop. F: 18X6 28X6 R: 17x10 305/45
  4. J

    Free to me GMC 2500

    Verify the correct pressure at the rail, them get a noid light to make sure the injectors are firing (assuming they are plugged in in the correct order)
  5. J

    Javlin42: My 1994 RCSB Build Thread

    Outside for now covered in pollen until parts arrive. Wish I had a little more sidewall front and rear but it is what it is.
  6. J

    Javlin42: My 1994 RCSB Build Thread

    Figured out the issue with the caliper clearance. There was hub centric rings on the axles that weren't required with this brake setup. I had to get a conversion joint for the new yoke. And for now, got some braided lines on. I got ground the rivet heads and knocked them out and pulled the...
  7. J

    Javlin42: My 1994 RCSB Build Thread

    Just a 80 shell off ebay with a $40 billet insert. I think after the hood and door get painted I'm going to swap out the black housing lights for a stock looking set. And thanks, not to bad for my first time
  8. J

    Javlin42: My 1994 RCSB Build Thread

    I appreciate it. Yeah it's a pretty nice piece. Moser M9, 35 spline, wilwood 13in big brake kit, all the bells and whistles. The grill shell that I bought for this truck fits perfect. The replacement Filler strip that goes under it that I got from lmc was about 1.75" short per side. Luckily I...
  9. J

    Javlin42: My 1994 RCSB Build Thread

    Alright, got some help to set the bed on and centered back up. I think it's going to work. That was the easiest but stressful part. Now to take it all back a part and weld my brake line brackets on, make brake lines, assemble the assembly, traction bars and drive shaft. I will say to...
  10. J

    Javlin42: My 1994 RCSB Build Thread

    Alright, this week's project has began. Got the bed pulled off and started the disassembly. And threw the next housing in and axles. Just test fitting everything just in case. Waiting for some help to set the bed on then time to make brake lines and final assembly on the rest of the components.
  11. J

    Javlin42: My 1994 RCSB Build Thread

    I mounted these today. If the weather cooperates the rest of the week, I'm going to get the bed set off and hopefully install the new rear axle. Still skeptical that this wheel/tire combo will fit but we shall see.
  12. J

    Interior light problems

    This is the point I'm trying to locate. Because I've checked what I believe is everything up to and after this
  13. J

    Interior light problems

    Just the under dash lights come on. No dome, and mirrors still don't work. I'm trying to locate the junction of where all the wires split from. Because I can unplug the harness at the kick, and apply power and turn the overhead lights on and they work fine. Plug the harness back in and apply...
  14. J

    1997 L31 Vortec 5.7, 187K Miles Almost Complete

    Do you have the upper radiator mounting brackets available?
  15. J

    90-1500

    Just went through your hole build thread. Killer work bro, I think you will be happy with the TKX trans and the coilovers. I recently did that trans swap as well as a coilover conversion (ridetech) on a customer vehicle. How do those tmi seats sit? Looks like you gain a ton of leg and head...
See more

Latest posts

Staff online

Members online

... and 25 more.
Total: 1,502 (members: 75, guests: 1,427)

Forum statistics

Threads
64,540
Messages
1,396,181
Members
51,943
Latest member
rbrook95

Share this page

Top