-
-
HawkDsl replied to the thread Stock ride height.Yes, drive it around. Funny story: I bought my truck new, and when it showed up at the dealer, it leaned to the left. I asked about it... -
Drive it around, they will settle
-
HawkDsl replied to the thread Clunk When Turning.Raybestos also make good steering components. It's what I used for my front end rebuild.
-
HawkDsl replied to the thread Clunk When Turning.Another idea is to set up a vid camera in the area of the clunk and see what happens. Doesn't need to be a go pro or something...
-
HawkDsl replied to the thread 88 5.7 low on power.Looks like allot of veins to me, but your mileage may vary. I gave decent advice, and the ADL jumper is a good start. I bought my 89...
-
HawkDsl replied to the thread Humming on deceleration.My 89 hummed in the rear sense new. GM rears are usually indestructible with regular driving. Good idea to have a look, but I suspect...
-
It's leaking somewhere. Brakes are a closed system, if you are losing fluid it's leaking. You just gotta find out where.
-
HawkDsl replied to the thread 88 5.7 low on power.an 88 is OBD1, scan tool is not going to be much help. You can jump A/B terminals in the OBD connector under the dash (), and the codes...
-
HawkDsl replied to the thread Rebuilt Motor Backfiring No Start.Yes, if SBC, your 180 out. double tripple check you got the right wires going to the right plugs.
-
HawkDsl replied to the thread Ghost Brake Fluid!?.Nothing on the ground usually is a dead ringer for behind the master. Hydro clutch will do the same thing, and usually is eating up your...
-
HawkDsl replied to the thread 1993 Yukon crate motor hydraulic roller lifter cleaning and adjustment journey - (Solved).First thing that pops to my mind is that you have a leaking intake gasket, and it's ingesting water... The other is that you suddenly...
-
HawkDsl replied to the thread Windshield replacement woes.Mine was at the top lip, but it was just surface rust. I imagine the salt belt states could be bad. That was all fixed when my truck was...
-
Getting mine replaced today and I was concerned about the install horror stories I've seen, like the OP had. My installer sent me this...
-
HawkDsl replied to the thread Windshield replacement woes.That's a good example of the second design seal bulge (right at the lip of the door. The flat black/not shiney rubber is the end seal)...
-
HawkDsl replied to the thread Windshield replacement woes.UPDATE: Urgent!! LMC is still selling the first design glass... I have one sitting in my bedroom right now waiting for the spring. They...
-
-
Loading…
-
Loading…
Staff online
-
kennythewelderOfficially Retired, B31-3 (6-G) certified welder.
Members online
- 99xcss4
- l1lartur0
- Supercharged111
- SlamTheMan
- JozefRoberts
- L31MaxExpress
- Road Trip
- Smittyrcsb
- goldtop
- Caman96
- TheTinMan
- Bachert24
- dallasp438
- BuiltToWork
- Cunningham Machine
- GrandpaSpec
- Nick88
- OutlawDrifter
- Berdo97
- Stumpy
- Drunkcanuk
- Arthurius
- RichLo
- broncoetr
- supertech
- kennythewelder
- Wh4t3v3rs
- matt87
- elfbrew
- Freebirdinn
- DanB97
- Fredje
- nose__
- GmMasterTech
- BeXtreme
- 1998_K1500_Sub
- AB90Z
- heyitzjoel
- sntrym
- Pclayton89
- RhettR7707
- slow_c1500
- bpbrown
- DustyNuts06
- aaronb
- Hipster