Recent content by BNielsen

  1. BNielsen

    BNielsen's 2000 Chevy K3500

    Hopefully this mill runs as good as I think it will, it starts like a champ and has great oil pressure, not much blow-by, doesn't leak too bad
  2. BNielsen

    BNielsen's 2000 Chevy K3500

    Dropped it off today, hopefully going to pick it up tomorrow. Probably won't be able to give it a good shakedown run just yet but for now I'll drive it back and forth to work, I've got a feeling there's going to be plenty of things wrong I'll find in a short amount of time.
  3. BNielsen

    My GMT800, 2003 RCLB 2500HD Build / Rebuild!

    Well maybe it's a good thing I can't get an answer from them. I've been looking at the Wardens for like, 5 months now but they're still out of stock. I've emailed them asking when they'll be available again, but going off your experience I guess I'll go a different route. Did they just wear out...
  4. BNielsen

    Build a hypothetical 3500HD.

    I think there's a bit of a skirt to the flatbed, that's why it looks so low. I think most aftermarket conversion companies used leaf springs; everything I've seen that's been SAS'd like Monroe trucks or Quigley vans have been leaf sprung. Coils/3-link could be the key to a reasonable height...
  5. BNielsen

    Tray for 2nd battery

    Honestly if it wasn't so hokeypoke looking I may have left them, my CB does have a PA output and I toyed around with putting a small speaker behind my bumper or something. The car alarm angle is interesting though, I never thought of that, I assumed it was just a PA since the truck had a CB...
  6. BNielsen

    Tray for 2nd battery

    I installed the storage box in my 96 the day after I brought it home, the PO's had some wonky PA speaker and horns in that space.
  7. BNielsen

    Tray for 2nd battery

    I wonder if the driver's side tray was snatched out of my crew, it didn't have one when I got it. My old 97 Suburban had one, I removed it for an underhood storage box; and my 96 K2500 didn't have anything.
  8. BNielsen

    Build a hypothetical 3500HD.

    There's a picture floating around of an insanely low 3500HD 4x4; I think I have the picture saved somewhere. Following the thread though; always wanted an HD but I'm content with my K2500 and K3500, they'll do everything I want them to do. ---EDIT---- Found it.
  9. BNielsen

    BNielsen's 2000 Chevy K3500

    Still got some stuff to do, windshield guy is coming Tuesday to replace the glass, there's a leak I think chased to the top of the windshield and I think the seal is bad, I can move the glass a couple of centimeters back and forth and almost see some daylight. Still got a couple grounds to...
  10. BNielsen

    0411 swap L29, now no idle

    When I did my 0411 swap my truck idled like dog **** but ran fine; what it wound up being was a blown Eng-1 fuse for the MAF sensor. Maybe check that?
  11. BNielsen

    $600 2000 C3500 CCLB

    I was gonna offer a reasonable amount, but honestly I probably would've wound up parting it out; I don't trust fire damaged vehicles. They're never right even if you replace everything burnt.
  12. BNielsen

    Misc. GMT400 Parts Hoard

    I can grab them, my buddy hauled it off but I said I still needed some parts; I'll holler at him some time this week. If I can't pull it out of the parts truck I'll try to grab one next time I find myself at LKQ I can grab the full thing, how's $20 sound?
  13. BNielsen

    Misc. GMT400 Parts Hoard

    I can probably grab some for you, I sold my parts truck but I didn't have time to pull the harness, I can at least get the harness and rubber seals.
  14. BNielsen

    $600 2000 C3500 CCLB

    I'd been eyeing that truck for months. I was fixing to message that lady once I got home from my honeymoon
  15. BNielsen

    88GMCtruck's 98 Silverado Towpig Build: "Black Fox"

    I wanted a B&W for my red truck, but with it already having all the holes drilled for rails I just decided to go that route. My crew cab on the other hand is gonna get a weld in B&W turnover center piece since at some point someone welded a big ass chunk of 1/2 C-channel and a fixed ball in the...
Top