Recent content by 93M6Formula
-
1996 GMC K3500 Dually Build
Finally got my frame and parts back! Turned out absolutely perfect. Now to get some suspension and steering parts so I can make it a rolling chassis again.- 93M6Formula
- Post #131
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Not a whole lot to update right now, still waiting for my frame to get done which was supposed to be done 3 weeks ago... Engine is basically done and ready to put in once it gets here. For now, i've been finishing my turbo build on my 93 Formula to keep me occupied lol.- 93M6Formula
- Post #130
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Been a minute since i've updated... Been waiting on parts then I had to wait for warmer weather to get some painting done, then I broke my arm so that slowed things down... Because of who I am as a person, I couldn't bring myself to use the original crusty CP3 injection pump so I ordered a...- 93M6Formula
- Post #129
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Another small update. Decided to bite the bullet on head studs, but I went with KB Diesel over ARP, $650+ for studs is just stupid... But I got the heads on and started getting the valvetrain cleaned up and installed.- 93M6Formula
- Post #127
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Hoping I can get some less boring updates here soon lol. Cold weather and house projects take a toll on some of this but hoping soon I can get out and finish cleaning up the frame and getting that ready for blasting and powdercoat within the next month or so.- 93M6Formula
- Post #126
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Well, a small update. Got my new rod bearings and cap bolts, I pulled the pistons back out to reclean everything then re-assembled. Spins MUCH easier with the bearings oriented correctly... With that, I could FINALLY move on to getting the bottom end buttoned up, timing gears installed, oil...- 93M6Formula
- Post #124
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Well... Minor setback. Feel like i'm getting nowhere on this engine. I mentioned above that the engine was turning over way too hard, infact it was locked up once the last rod was torqued down and clearly that's an issue. So I pulled a few caps and noticed a few of the bearings were scored...- 93M6Formula
- Post #123
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Kinda slow progress but got further on the shortblock. Finally got my parts washer cleaned out and some fresh fluid in it so I could clean up the rods and pistons. That all went well but I tell you what, never building an engine in a non climate controlled garage again. Every time I turn on my...- 93M6Formula
- Post #122
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
In this case I simply cleaned it up with a wire brush, let it soak in muriatic acid for about 20 minutes, rinsed in distilled water then put it in. Eventually I want an abrasive tumbler to do that then probably still etch with acid and rinse. I could have also used my power supply to do rust...- 93M6Formula
- Post #121
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
That's where i'm at for now. Finally got my parts washer cleaned out and a new pump so i can clean up the cam, rods, pistons, and lifters, then move forward with assembly. My heads should be done at the machine shop soon which will be about right on time. Probably take a break for a bit to...- 93M6Formula
- Post #119
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Small update. Been a little busy but been prepping the block for assembly and measuring all my bearings clearances which has been a pain.... I think the up and down temperatures have been messing with my measurements since I don't have a climate controlled garage and we're talking tiny numbers...- 93M6Formula
- Post #118
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Picked up my block and crank yesterday. Now the assembly can begin! Can see the sleeve install here.- 93M6Formula
- Post #117
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Also test fit the replacement tank crossmember. Surprisingly fit very well, was worried with it being Dorman.- 93M6Formula
- Post #116
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Spent last night dropping my mockup block and 6L90 in. Dropped right in and fits perfectly. Once I convert this to 4WD, I will be able to use the factory mount and everything. The mount ended up about 1/2" forward but luckily the stock crossmember has notches and enough room for the...- 93M6Formula
- Post #115
- Forum: Street Build Threads
-
1996 GMC K3500 Dually Build
Got my rear spring hangers, shackles, and rear tank brace in. Decided to replace that brace also, it's not rotted out but it's got some good pitting and just looks ugly so I figured why not.- 93M6Formula
- Post #114
- Forum: Street Build Threads
Latest posts
-
Another 454 Vortec Build Thread - Documenting, Q&A, Help
- Latest: Supercharged111
-
-
-
-
Members online
- Joshua Gonzalez
- 94WarHorse
- Remodelmaster
- PeacefulStorm
- Drunkcanuk
- matt87
- PolarBear
- Rusty_dusty
- Supercharged111
- WAM62
- Carlaisle
- Buzzburns
- missouritig
- bapbap
- Road Trip
- Travon
- fancyTBI
- Moparmat2000
- JPVortex
- Bachert24
- jdonnell
- TheKOOK
- 95OBSMan
- Caman96
- spradilak
- local_ignitro
- Leano127
- Twiztedmods
- AuroraGirl
- GunnyRob
- PlayingWithTBI
- Kevmore007
- heyitzjoel
- Alteca
- Gordy_
- isomswim
- SuperSpore
- boreas
- Carlosm86
- DeskPop916
- mabco01
- 0L94fan
- skidmrk
- Lowsport14
- 99xcss4
- TexasLS1
- patrick5050
- Big1block
- tayto
- boy&hisdogs