Search results

  1. L

    reverse cluncking

    95 ex cab short bed z71 cluncking when going to revers, u joints are good, no carier bearing, and only does it going to revers. I can put it in park and roll the truck back and forth and it doesn't make any sound. Doesn't mater if it's park to reverse or neutral to reverse also does it when...
  2. L

    distributor Change, now long crank before start.

    Changed the distibutor in my 90 tbi 350 and it wouldn't start, put the old one back in and now it cranks for 15-20 seconds before it starts. The reason for changing was the motor would randomly die but the new one wouldn't even start it (guess its bad) Timing was set to zero with brown/black...
  3. L

    90 5.7 randomly dies but starts right back

    Just traded off a truck for a 90 step side the supposedly has a 93+ 350. But going down the highway it just randomly dies then will start back ~30 seconds after. The guy whent through the hole ignition sysem. And it didn't fix it. What could be causing this? If its electrical, then were...
  4. L

    front bag questions

    I'm wanting to bag my frontend but don't want to run a tank, just a compressor, adjustable pressure switch. Is this possible or do I have to run a tank I'm not trying to lay frame just wanting a little drop to mach my 7" in the back (flip plus shakle) and for a better ride. Also trying this on...
  5. L

    non console floor shifters.

    My 4.8 swap has been done for a few weeks now, so its time for a 4l80e to go in. Already got parts to repair my harness, new mlps switch, and my trans go hd-2. Now I need to order a cooler, fly wheel/ spacer and bolts, tune, and a shifter. I've been looking at the b&m unimatic. I Like the t...
  6. L

    4l80e guys! need some shift cable pics

    Title says it. I need some pics of the cable routing and how it all hooks up. Going from a 5 speed to 80e and want to retain factory look. Post up! Thanks
  7. L

    4 peice slide back glass lock

    Any one know were to get a replacement latch for a rear 4 piece sliding glass? And how to change them out?
  8. L

    be my judge: 2 or 3 more inches

    Title says it, be my judge on picking my drop spindels. Its lowered 7 in the back, and 3 in the front. Its got 275/45 20 all the way around but the rears are getting balled so the front can go to the back and skinyer tires could go on the front if needed. So should I go 2 or 3 Pic
  9. L

    5 to 6 lug with 14b sf and flip kit

    In early stages of 5 to 6 lug swap. I'm down to the part of how to make the flip kit work with out buying a hole new kit. All I need is the saddle, u bolts and plats with the off set hole to move the axle back so the slip yoke doesn't bottom out. Any one know were to source these parts out?
  10. L

    lost brakes all at once

    Drove my 95 c1500 rcsb to haul the naboors heavy snap-on tool box. All was OK and did bottom the "pumpkin" on the bed a time or two. (Flip kit out back) but nothing to hard. After that was unloaded we had another trip to make. During that trio the brakes were very touchy then at my last stop...
  11. L

    any one running quad tips like a vett?

    Been pondering the idea of quad tips like a vett with a roll pan. Either a smooth pan with 4 tips flush in the middle spaced out like the vetts or a c5 type pan with out the tail lights and 4 tips in the middle. I'm slammed in the back so I think it would look pretty sweet with quad 3 or 4"...
  12. L

    nv3500 poring gear oil out!

    My 5 speed is puking gear oil out like crazy! Done a 4.8 motor swap, truck is running good, new clutch kit and rear tail seal and a 5-6 minute drive it dumps every bit of 2.5 quarts out! Iv already spent $90 on gear oil so far, 5 quarts for this one reason (2.5 before the new seal and the other...
  13. L

    bleeding slave cylinder

    Tryed gravity bleed, revers bleed and traditional pump the clutch and i got it to brake the staps on the new slave cylinder but its not enuff to disengage the clutch. Master cylinder was good when I parked it for my motor swap and my slave had a small crack were the line whent in so I replaced...
  14. L

    black can with vacuum line

    What is the black can looking thing on the driver side up by the radiator? Tried searching but i dont know what its called. Can it be removed to tidy things up? I don't have emissions so if it has any thing to do with that, its not a problem. Thanks guys
  15. L

    oil sender problem

    Well, I got a little to happy cutting unneeded wires for my swap, and cut the oil sender plug off, and left the old distributor plug (woops) now the wires for the oil sender are mixed with a bunch of other wires and some of the same colors. I found the wire that goes to the cluster, and I think...
  16. L

    LOWnEASY,s 95 5.3 5 speed build

    got a buyer lined up for my 350 tbi motor so it came out today. now im talking to a guy local with a 5.3, and iv spotted one on ebay so as soon as the guy comes and gets the old motor i will be picking up or ordering my a 5.3 i still have to order a few fuel part but so far i have my fuel pump...
  17. L

    what heater hoses to use?

    What heater hose work on the swap? 4.8/5.3 truck motor to be specific. Do the stock v8 obs hoses work? On a side note, Motor is coming out tomorrow and time willing, I'll be putting my fule pump in. Still sourcing a motor if any one has a complete 4.8/5.3 with accessories harness starter and...
  18. L

    manual window handle removal?

    How do I remove the window handle on my doors. Its a 95 if that matters. I thought there was a clip but I can't see any thing. Any helps is appreciated. Thanks :rockit:
  19. L

    anyone done any thing with a W/T grill?

    Anyone done anything "custom" to make the w/t grill look half decent? Iv been pondering the idea of cutting the webbing out and bending up some 1/8" or 1/4" bar to give it a billet style look. Been looking for a good used Silverado grill but haven't found any good deals yet. So has any one...
  20. L

    any easyer way to drill holes for c noch

    Title says it all. I spent an hour yesterday and only got two holes drilled! Got a brand new $16 titanium drill bit. I'm 6 ft tall and 210 lbs and its eating my lunch. Lol. I don't have access to a welder neither! Any tips or tricks?
  21. L

    2" spring hangers

    Just done a flip kit and took these off. there belltech 2" lowering hangers. $60 shipped to your door. Pm me for any other question. Will put Pics up shortly. Pay pal only
  22. L

    flip kit + 2" hanger + 1" lift shackle

    Can I get away with the combo mentioned in the title and still be able to get a good pinon angle? Can't seem to locate any stock hangers that don't cost an arm and leg!
  23. L

    this the right flip kit?

    Just got my flip kit in the mail and it don't look right com paired to the picture on summit and djm's web site. It looks like the 99+ kit. Part number on the box is right though. Djm fk1025-6 here's a pic I also have the rest in that isn't in the pic (u bolts c-notch and hardware)
  24. L

    "ls swap" fuel pump with TBI 350?

    Got a head start on parts and ordered my mount plates, fuel pump, 98 camaro/firebird temp sensor, and my oil sender adapter. It will be anouther month or so before I get my motor and I'm ordering a flip kit tomorrow witch will be here well before the motor. So when I install the flip, can I go...
  25. L

    nv3500 to 4l80e swap

    I was originally going to go with a t56 But there are more 4l80e's to be had around here for far cheaper, so here's my question(s) I'm swapping a 5.3 or 4.8 into my 95, and wanting to go with a 4l80e. What do I need. Trans, TC, lines, cooler, shifter (cheapest floor shifter that will work)...

Latest posts

Staff online

Members online

Total: 1,364 (members: 38, guests: 1,326)

Forum statistics

Threads
64,550
Messages
1,396,358
Members
51,975
Latest member
Machlen

Share this page

Top