Search results

  1. S

    a little louder for free?

    It has a flowmaster muffler and y pipe already. It was dumped about a foot before the rear axle but was too much for me in the cab. I ran pipes around the rear axle and dumped it after and was happy for like 3 months but want it a little louder. If I drill a hole after the muffler in each of...
  2. S

    easy way to fix alt?

    I did the big 3 and all was well but I nicked the plastic surround around the alt positive and slightly pulled it out and believe I half shorted something. I was reading 12v at idle and 12.7 off. Just wondering if there's a diy or is it really cheap to fix? It's currently ghetto rigged with a...
  3. S

    clutch fan nightmare.

    Well I just got my intake manifold gasket done and saw my clutch fan was free wheeling and could be stopped by hand. So I did the right thing and replaced it and replaced it. .. I've replaced it 4 times so far (all hayden severe duty 2 from aap, 1 RA, 1 oriley) and everyone freewheels at...
  4. S

    overheating.

    I did a full flush, new themo, new clutch. Everything worked perfect and temp was one tick below 210 for 2+ weeks. Today I was driving and things started overheating. I thought clutch maybe went bad as I could stop it with my hand but I tried another, then another all 3 can be stopped by hand...
  5. S

    engine oil

    I'm about to change the oil soon for the upcoming warmer weather in the truck and I'm wondering to use 10w30, I'm using 0w30 To my understanding both have the 30 so the warm thickness will be the same but cold engine 0w30 will be thinner and flow better at startup. Am I missing something or is...
  6. S

    do fan clutches often come bad new?

    I just put a severe duty in for texas heat but it doesn't seem to disengage. Lots of resistance cold and hot as well.
  7. S

    full coolant flush

    95 5.7 tbi I'm not sure the last time the coolant was changed and have a new thermostat, clutch, and cap on the way.. will also get hoses if need be. What is the easiest way to flush the entire system in 5th grade instructions?
  8. S

    2wd torque specs

    Would someone be kind enough to supply c1500 upper/lower bj and inner/outer tie rod torque specs... I don't have a service manual and everything I've found is for 4wd just want to make sure for my 2wd. Thanks
  9. S

    truck drifts to right 2.. good alinement

    I have a good alinement and a lifetime warrenty at firestone. New outer rods and sleeves, new upper bushings, lowers don't have any play as well as idler and pitman... how do you test the upper tie rods to see if they're good (I was lazy since it started raining and didn't do them)? New...
  10. S

    anyone have a grill gaurd like this?

    I don't care about brand just want the style. Go rhino 3090b. square style. Gaurd without the "euro" headlight bars and stuff or it really doesn't matter... don't feel like paying 250 on the old truck.
  11. S

    seat locked in position

    I have power seats but the passenger has manual forward and backward (I think). The chair is locked in the front position. How do I release it to move? I've tried all the levers on the bottom manually but it doesn't move.
  12. S

    Gas gauge problem

    Just replaced the entire fuel pump assembly. My gas gauge still is a little bouncy.... When reading through the hummingbird fix I feel I do not have the same issue. My needle never really vibrates, it "bounces" or as the first youtube video that popped up described it "dances". Any ideas...
  13. S

    heated o2 necessary?

    Putting in a flowmaster y250300s y pipe and a high flow cat (already have a FM muffler single to duel turndown). Will the single wire o2 sensor heat up fine or will i need a heated o2 with the upgrade? 95 1/2 ton

Latest posts

Members online

Total: 1,059 (members: 29, guests: 1,030)

Forum statistics

Threads
64,487
Messages
1,395,040
Members
51,791
Latest member
WrenchAndRatchet

Share this page

Top