Recent content by chevy_man

  1. chevy_man

    Couple Fuel Pump Questions...

    IIRC, taking the bed off is simple as: 8 bed bolts, 3 filler neck bolts and 1 ground, and un-plugging your tail lights under the bumper (or you can unplug them from the back of the lights and drop the harness down if someone has hard-wired them). Get a buddy to help you slide it back 12-18" and...
  2. chevy_man

    Help.... Truck not running

    From 87 to 95 the trucks had OBD1. However, all the jumper will do is flash the codes. To reset it you need to disconnect the battery for a few hours.
  3. chevy_man

    Help.... Truck not running

    Some truck specs would be a good start. But if I had to guess since you can see the injectors that you're dealing with TBI. Sounds like your injectors are flowing way to much fuel. Could be the injectors themselves or a computer issue, although when I lost a computer mine wouldn't open at all...
  4. chevy_man

    5.3 or 6.0 swap in Arizona

    That's actually a damn good price for a fully rebuilt motor and install, as long as the install includes all the wiring. Most people spend that much just getting a junkyard motor swapped themselves before they're done with it.
  5. chevy_man

    Vacuum line hookup for 700r4 lockup harness

    You could get the diesel lock-up valve setup from one behind a 6.2. Mine actually has one because it was built for a 6.2 blazer and I scored it for super cheap. It's also kinda nice knowing there are no electronics in it. My connector is only plugged in to keep it clean. I'd just grab a T...
  6. chevy_man

    Vacuum line hookup for 700r4 lockup harness

    Is this something aftermarket that you're trying to add onto your existing transmission? If you need vacuum there are several un-used ports in the throttle body IIRC.
  7. chevy_man

    Chasing OBD2 codes for inspection

    Word Best thing I've done to mine. Runs way smoother now. Although mine was running super rich with the poppets, they'd stick and just dump fuel. Plus, a set of fel-pro's and cap/rotor while you're in there doesn't hurt. The inside of my intake was dirty as a hookers ****** where the EGR...
  8. chevy_man

    High Pressure Power Steering Hose

    Definately easy to do. Also, the hoses last a lot longer if you don't hold the steering wheel against the lock and build the pressure way up. Usually it's the crimp that fails, and the pumps build their max pressure when you're trying to push on something immobile (like the stops on the knuckle).
  9. chevy_man

    HELP! 92 gmc 5.7 has no spark

    Yes, I had an alternator fail and take out my ecm. But it also stopped the injectors, not just the spark. I'd try another ignition control module, if your timing is correct. I've had them DOA on me before. Also check your wiring connections inside the distributor to the module. I had a wire...
  10. chevy_man

    97 shortwide vortec

    No, they don't like ****** parts that don't match the OEM specifications. BUT, I've run those same plug wires with no issues, so I'd be inclined to think his set may have had a factory defect or something else going on with the truck. Hell, if it was "sputtering that nasty" he may have had 2...
  11. chevy_man

    Better MPGs?

    Tune-up. New plugs, check your wires, new cap & rotor, new air filter, fuel filter, synthetic oil front to back (trans, t-case and diffs will compliment the motor) has been shown to give 2-5% (not much, but it's something). Not a bad idea anyways as synthetics have been proven many times over to...
  12. chevy_man

    2000 K2500 old body style with vortec 350

    IMO, don't chase horsepower and get a cam to increase your torque. I have a 00' K3500 CCLB w/4.10's....same truck basically, had the L31 stock. It's great once you get up to 20mph or more. The bottom end just isn't great with the factory stall and fairly high 1st gear in the 4L80e. I'm going...
  13. chevy_man

    How Much Can YOU Haul IN 1/2 Ton???

    Made a run to the dump with 2800#'s. Had no idea as it quit sagging when the overloads hit. That damn spring pack was tough. Now my K3500 literally won't move. I put 900#'s into the bed and measured a 2" drop at the fender openings. Made me realize just how much **** people are packing into...
  14. chevy_man

    350 motor question

    Trans wear is not an issue, maybe the clutch but that depends more on the driver. Manual transmissions aren't very picky like autos.
  15. chevy_man

    WOW!!!!! BIG LOAD

    Boats aren't that heavy. He also has 3 trailer axles under the only heavy part, which I would assume is 2 BBC's. The rest is just fiberglass. Other than being slow, as long as he has decent trailer brakes there's really no issue towing that with a 1500.
See more

Latest posts

Staff online

Members online

Total: 2,164 (members: 49, guests: 2,115)

Forum statistics

Threads
64,475
Messages
1,394,710
Members
51,752
Latest member
moverton05

Share this page

Top