Search results

  1. atyates

    New steering gear box

    If you end up doing this pm me with the results. I've been thinking about it myself
  2. atyates

    New steering gear box

    Well I'm trying to get rid of my steering slop and have replaced everything from the rag joint to idler and putman arms and tie rod ends. I can still turn my steering wheel from 11:00 to 1:00 without the tires moving. What y'all think the steering box? And if so what steering box do you...
  3. atyates

    Rack and pinion conversion?

    I'm not sure but if it will steer as good as our other two vehicles it will make a 100% difference having rack and pinion
  4. atyates

    Rack and pinion conversion?

    Anyone done it? I bought my truck new and all my steering parts have been replaced twice and need to be done again. My ford truck and my wife's durango handles/steers better than my 97 k1500 did new. And they both have 150k plus on them with rack and pinion
  5. atyates

    How to adjust the steering box

    I know this thread is old however I just adjusted mine word for word like the op said. I took it for a test drive and it feels like it wants to pull me all over the road. So does this mean I need an alignment now or did I do something wrong? I losend the lock nut, snuged the allen bolt. Back it...
  6. atyates

    Xj steering shaft

    I got a xj steering shaft for those of you that want to do the swap. Nothingnwrong with it. Remember it only works for 95 and older trucks. $35 plus shipping from Georgia
  7. atyates

    411 pcm and cpc swap

    Is there anyone in the metro atlanta area that has done a 411 pcm swap and coil per cylinder swap in a Vortec 350? I've read everything I can on how to but I still don't know if I fill comfortable doing it myself. So I'm thinking about paying someone to come out and personally show me how to do it..
  8. atyates

    Front brake issue

    So I noticed my brakes slowly getting worse. So I decided to bleed them, because the calipers, lines ,pads ,rotors and shoes are fairly new. So I bled my rear and they were fine. When I got to my front passenger side I had my wife in the truck pumping and holding the brakes, barely any fluid...
  9. atyates

    Sudden rough idle

    So my 97 vortec 350 starTed running rough at idle today. Only at idle. It's 100% wile I'm driving. It also started taking longer to start. It did throw a p1153 code wich is for the front oxygen sensor, but would that cause those issues? Thanks.
  10. atyates

    np241c rebuild

    has anyone ever rebuild that transfer case? it seems pretty straight forward but I was wondering how many people have done it and how difficult it is?
  11. atyates

    No air on driver vent only

    I have a question similar to this problem. everything works fine on mine. got good air flow through driver vents, but dont have any through the 2 passenger?
  12. atyates

    can someone give me these rims?

    can someone photooshop just these rims on my truck? thnks in advance
  13. atyates

    any one looking for a new engine or tranny?

    just thought I would post this for those interested this motor here is a factory replacement for vortec 350. uses factory intake manifold and fuel injection and requires absolutely NOTHING special EXCEPT a computer tune. other than that it just drops right in, in place of your old worn out...
  14. atyates

    BAD vibration while towing

    100% sure it doesn't do it without a trailer. was going 75 down the interstate for about 25 miles today. just as smooth as can be
  15. atyates

    BAD vibration while towing

    well its not the u joints. just replaced them with moog ones. still vibrates in this truck but not my other one. the trailer hitch is bolted and secure. the ball is on the receiver is tight. any ideas?
  16. atyates

    BAD vibration while towing

    whats the best way to know for sure if the u joints are bad? I got up under there and tried moving the driveshaft around on both ends and I didn't feel any play like that
  17. atyates

    i know,i know, another cam question

    i want to put a cam in my truck, keeping everything else stock. will this cam work without having to do anything but a re-tune? http://www.summitracing.com/ga/parts/cca-08-302-8/overview/make/chevrolet
  18. atyates

    BAD vibration while towing

    oh. I see that now. well it still wouldn't make since of why it doesn't do it under the same conditions on my other truck
  19. atyates

    BAD vibration while towing

    yeah I have no where near that much air in my trailer tires. and like I said, the trailer pulls fine with my other truck
  20. atyates

    Rear Drum to Disk Conversion Spacer Plate Spec's for 2003 nbs to 88-98 obs.

    I had to get a local machine shop to machine mine cause I couldn't find any spacers online anywhere
  21. atyates

    BAD vibration while towing

    I guess it could be the u joints. but weight shouldn't be a problem. its only a 6 foot, single axle trailer with a 4 wheeler on it.
  22. atyates

    BAD vibration while towing

    so my truck, details in my sig, has a bad vibration at highway speeds between 70-75 mph while towing. wont go faster than that with a trailer. only while towing. it doesn't do it without a trailer. I just put all new bilstein hd shocks on it, checked, checked, and double checked to make sure the...
  23. atyates

    give me these wheels

    I would still like to see them on my setup if someone doesn't mind
  24. atyates

    give me these wheels

    what size are your rims and tires?
  25. atyates

    give me these wheels

    can someone photoshop just these wheels onto my tires for me? thanks

Latest posts

Staff online

Members online

... and 24 more.
Total: 2,314 (members: 74, guests: 2,240)

Forum statistics

Threads
64,664
Messages
1,398,282
Members
52,172
Latest member
Reject

Share this page

Top