Search results

  1. Bear Down

    Transfer case seal is killing me

    Thans
  2. Bear Down

    Transfer case seal is killing me

    Should there be fluid seeping or do I need to attach the yoke first before filling the t-case?
  3. Bear Down

    Transfer case seal is killing me

    Thanks for all support fellas. I’ll keep you posted on the install which I’ll be tackling this weekend, hopefully before game time.
  4. Bear Down

    Transfer case seal is killing me

    I know, I had to go back in the garage and check it lol
  5. Bear Down

    Transfer case seal is killing me

    cool beans, thanks. So with the sealant those dings shouldn’t be a problem, if I’m understanding correctly?
  6. Bear Down

    Transfer case seal is killing me

    Also, speaking on that “rubber bushing”? Does that need to be replaced, and what do u thinking about those marks I mentioned on the previous images?
  7. Bear Down

    Transfer case seal is killing me

    Bad angle on the photo I believe that’s a rubber bushing on the end of the shaft
  8. Bear Down

    Transfer case seal is killing me

    I thought that was grease, not so?
  9. Bear Down

    Transfer case seal is killing me

    Good evening buddy got it out did make a few marks on the inside. Should I be concerned with them?
  10. Bear Down

    Transfer case seal is killing me

    I’ve been looking at the Lisle. I’m gonna give this hole drill method a shot first. Thanks for the advice about that spring too
  11. Bear Down

    Transfer case seal is killing me

    In your opinion from the pictures I provide have i did damage to the case specifically where the lip should be I believe I can get it out but I’ve made some indentation marks in that area.
  12. Bear Down

    Transfer case seal is killing me

    Any takers in this situation ^^^^
  13. Bear Down

    Transfer case seal is killing me

    Gave it a go, worked around the edge, didn’t find a lip. I think I might have an issue because I know there should be a lip but it appears to be case. Take a look?
  14. Bear Down

    Transfer case seal is killing me

    Cool beans, I’ll give it a go when get home.
  15. Bear Down

    Transfer case seal is killing me

    So it appears on the video there is a lip. Is it that I just don’t see it because its flush?
  16. Bear Down

    Transfer case seal is killing me

    Thanks for the replies fellas. Just so I understand I can place a pry tool of sort between the seal and case (arrow on the image) I’ve nicked the surrounding edge twice as shown in the image
  17. Bear Down

    Try to delete post

    Having a hell of a time with this output shaft seal replacement. It appears that the current seal is recessed inside. I believe it should have had a lip like the replacement seal I purchased. can’t seem to remove it with any seal tool with possibly causing damage to the surrounding area. Has...
  18. Bear Down

    Error

    Having a hell of a time with this output shaft seal replacement. It appears that the current seal is recessed inside. I believe it should have had a lip like the replacement seal I purchased. can’t seem to remove it with any seal tool with possibly causing damage to the surrounding area. Has...
  19. Bear Down

    Transfer case seal is killing me

    Having a hell of a time with this output shaft seal replacement. It appears that the current seal is recessed inside. I believe it should have had a lip like the replacement seal I purchased. can’t seem to remove it with any seal tool with possibly causing damage to the surrounding area. Has...
  20. Bear Down

    Transfer case stupid question thread

    Having a hell of a time with this output shaft seal replacement. It appears that the current seal is recessed inside. I believe it should have had a lip like the replacement seal I purchased. can’t seem to remove it with any seal tool with possibly causing damage to the surrounding area. Has...
  21. Bear Down

    Rough Country 4"/6" kit install tips.

    Good evening, running into the exact same problem. Grinded down bump stop and notched it, but it seems to be hitting the welds on the shock mount, leaving a gap approximately 5/8” which is bigger than the supplied washer. How did you solve this problem? I’m concerned that grinding the welds may...

Latest posts

Staff online

Members online

... and 17 more.
Total: 1,613 (members: 67, guests: 1,546)

Forum statistics

Threads
64,539
Messages
1,396,158
Members
51,942
Latest member
Joshua Stone

Share this page

Top