Search results

  1. jerry mize

    Axle damage

    I got a set of gt4 g80 axles for my truck installed the front and rear came time is put in the new breaks found damage to the axle tube on the driver side do they make a repair kit ? Or do I just bend it back out and hammer in a sealed bearing ? Any ideas the last pic is just because it was...
  2. jerry mize

    Help

    I have changed everything at this point except distributor and a crank sensor
  3. jerry mize

    Help

    It has no codes or check engine light that's one of the the things puzzling me because I feel that it should
  4. jerry mize

    Help

    Truck has a true duel set up with no cats
  5. jerry mize

    Help

    Yes it will in park or neutral you can red line it
  6. jerry mize

    Help

    I went back switched all the electricals from old engine to new engine earlier and did ecm reset the only thing I haven't done is switch the distributor because when the rod snapped it flug up and broke cam shaft didn't know if the old distributor shaft was screwed or not
  7. jerry mize

    Help

    It's about 156 to 160 across the board
  8. jerry mize

    Help

    I honestly don't went back through checked valve lash and ran compression test all are in margins of normal compression is on high end of normal
  9. jerry mize

    Help

    I've checked fuel pressure and flow also put the after market throttle body that was on old engine on plus new cap rotor and plugs and switch m.a.f and map senor went back through all grounds just to check
  10. jerry mize

    Help

    And on the left
  11. jerry mize

    Help

    You would think but wheres the help ?
  12. jerry mize

    Help

    I have all the old engine parts I didn't reuse anything because most parts were aftermarket and above stoke figured they helped with slin the rod out of #5 I'll try switching the whole throttle and let you know also I appreciate the link I'll print out and add to my archives
  13. jerry mize

    Help

    Thank you for manual link though I will print and add to my archives
  14. jerry mize

    Help

    I still have the throttle body from first engine so you think I should just swap them and see what happens I didn't swap any of my old parts to new engine because I believe that my idea to upgrade everything before helped with slinging the rod to much rpm
  15. jerry mize

    What now?

    Does the truck have any codes I would start there but yes intake gasket can cause the simptoms you are having if the gasket is sucking air the ecm is trying to adjust I have had the same issue in my at one point as well
  16. jerry mize

    Help

    Swapped engine with low milage engine new engine will not respond over 2200 rpm I can't even hit passing gear there is no obstruction s to throttle everything. Is moving fine
  17. jerry mize

    Help

    It's like the peddle is going working fine just has no reaction
  18. jerry mize

    Help

    5.7 to 5.7 old engine slung a rod I found a deal on one with under 100k so I purched the truck yanked the engine and installed into my baby runs great doest skip or miss just want rev
  19. jerry mize

    The Stupid Engine Questions Thread

    I have 97 Z71 swapped engine new engine will not tach over 2200 while driving it's like soothing is wedged under the pedal " there is nothing stoping the peddle"
  20. jerry mize

    Help

    It's not skipping runs great just want tach up
  21. jerry mize

    Help

    Swapped engine in my 97 now it will not tach over 2200 any ideas
  22. jerry mize

    Performance help

    The new engine is supposed to be able to run the stock injection set up I ordered upgraded injectors and I have a after market throttle body from th old engine and cold air intake also have a msd distributor , cool and wires from old engine my intentions are simple this truck is baby I pull a...
  23. jerry mize

    Performance help

    I have a 97 Z71 k1500 the engine finally took a dump at 300k I have it on the stand but have already ordered a new 375 hp crate engine waiting for it to arrive wondering what upgrades are worth the money as I get things ready for new engine any help would be grate I already have after market...
  24. jerry mize

    Transfer case trouble

    Hey guys I have 04 chevy 6.0 awd question I lost reverse in my truck forward gears are fine I was underneath and was pulling tranny and noticed that when I turned the drive shaft the transfer case is making a loud grinding noise can transfer case no reverse ?
  25. jerry mize

    Anyone ever heard or seen exhaust plugged up or clogged passed the cats?

    For the fuel Injection to work at optimal performance for power and feul economy yes u need the o2 sensors it will however run with out them

Latest posts

Staff online

Members online

... and 10 more.
Total: 1,701 (members: 60, guests: 1,641)

Forum statistics

Threads
64,454
Messages
1,394,343
Members
51,700
Latest member
ceatea

Share this page

Top