Recent content by chevyboy1992

heater hose help

ok i got a wiring diagram from from my local gm dealer and i have all my wires marked.i just have to find the plugs to hook into the 1227730 ecm.if anyone has any input on what ive learned please fill me in i dont want to make a wire fire in my truck.thanks for the help though man i really do...
- chevyboy1992
- Post #12
- Dec 12, 2011
- Forum: Engine Performance + Maintenance
heater hose help

i did some research and i think i might can make my stock harness work.from what ive been told by jimsperformance i will use my stock ecm to run my trans and the 1227730 ecm to run my engine i just need the right wiring diagram because the ones i have dont match up.is it hard to do this...
- chevyboy1992
- Post #11
- Dec 12, 2011
- Forum: Engine Performance + Maintenance
heater hose help

ok im just new to splicing wires i cant seem to figure out the charts on my wiring diagram the colors dont match up i have a chilton adn a haynes book.
- chevyboy1992
- Post #10
- Dec 12, 2011
- Forum: Engine Performance + Maintenance
heater hose help

im running my stock distributer.with a hypertech 53,000 volt coil and 8 mm wires.only problem i have is i have to have the electronics for my transmission too does the f.a.s.t harness also have the trans wiring too?
- chevyboy1992
- Post #8
- Dec 11, 2011
- Forum: Engine Performance + Maintenance
heater hose help

my only problem now is i have to figure out what to do about my wiring harness
- chevyboy1992
- Post #6
- Dec 10, 2011
- Forum: Engine Performance + Maintenance
tpi conversion wiring harness

ok ive done some more researching and the way jims performance does it is he makes it where my stock ecm runs my transmission and the 1227730 runs my engine he just pulls the prongs from the stock ecm that run the engine and put them in the right locations for the 1227730 (camaro ecm) ive looked...
- chevyboy1992
- Post #5
- Dec 10, 2011
- Forum: Engine Performance + Maintenance
tpi conversion wiring harness

http://www.summitracing.com/parts/FST-301100/?rtype=10.i found this but im not sure if it will work
- chevyboy1992
- Post #4
- Dec 9, 2011
- Forum: Engine Performance + Maintenance
tpi conversion wiring harness

jims performance quoted me almost 600 for the prom burned and the harness rebuilt but if im right painless wont work because of my transfer case wiring will it?
- chevyboy1992
- Post #3
- Dec 9, 2011
- Forum: Engine Performance + Maintenance
heater hose help

nevermind that was a stupid question i just found it when you said front thanks for the help tempted
- chevyboy1992
- Post #4
- Dec 9, 2011
- Forum: Engine Performance + Maintenance
tpi conversion wiring harness

ok everybody im looking to see what my options are on my wiring to control my transmission and engine i have the tpi intake off of a 88 trans-am and a 4l60e transmission.i have checked with jims performance on getting my harness rebuilt into a dual ecm version and ive looked through books on how...
- chevyboy1992
- Thread
- Dec 9, 2011
- Replies: 4
- Forum: Engine Performance + Maintenance
heater hose help

ok on the left side of the throttle body or the front right side?
- chevyboy1992
- Post #3
- Dec 9, 2011
- Forum: Engine Performance + Maintenance
heater hose help

ok guys ive got my engine all set up its the intake out of a 88 trans-am and idk how to run the heater hosesfor this intake. im just trying to figure out how to get them run.can somebody give me a little help please
- chevyboy1992
- Thread
- Dec 9, 2011
- Replies: 11
- Forum: Engine Performance + Maintenance
intake problem

ok man thanx i might make some angled spacers so i dont put too much stress on one area.ill work something out.but i thought about my idea and the slots letting the intake move some how but the other eight bolts will hold it down and in place the 2 center bolts just mainly hold pressure between...
- chevyboy1992
- Post #36
- Dec 6, 2011
- Forum: Engine Performance + Maintenance
intake problem

so my idea is right? is that what your telling me.im sorry i dont understand what your trying to explain to me.but i really do appreciate the help.by opening the hole do you mean make it a slot instead of a hole?is my intake the wrong one?it came offf of a 1988 pontiac trans-am camaro has the...
- chevyboy1992
- Post #33
- Dec 6, 2011
- Forum: Engine Performance + Maintenance
intake problem

ok guys i have drilled and shaved and everything but pull out a torch(sarcasm) and i think i might have an idea it might be stupid but here it is.i thought about slottin the intake where the holes are and then i should be able to mount it easily and it should have enough strength not to brake...
- chevyboy1992
- Post #31
- Dec 6, 2011
- Forum: Engine Performance + Maintenance