Recent content by 9812VDuslly

  1. 9812VDuslly

    Looking for extended lug studs

    So listed underhead length is correct. Threaded length isnt.... Typical Doorman quality
  2. 9812VDuslly

    Looking for extended lug studs

    Ya mighta been. Bought the truck off a farmer in Nebraska. He had had enough with the 6.5 and looked like he took a hammer to the oil pan at one point lol Wouldn't surprise me at all if he stuck the wrong studs in the rear. I'll pull the wheel again and measure the threaded length. I bought a...
  3. 9812VDuslly

    Looking for extended lug studs

    Man, that's a great idea! I hadn't thought of the shanked lug nuts even tho all my Toyotas run them I'll measure the stud holes in the wheels when I get home and report back. I have no idea unfortunately what any of the wheels came off of. Guy I bought them from said they came with a truck he...
  4. 9812VDuslly

    Looking for extended lug studs

    Don't know brand name. Bought them used. Aluminum wheel thickness at mounting surface is .88 and steel is .49 is. So over an inch thick of wheels. They kind a look like a cross between G17 Evo and 9 Libertys.
  5. 9812VDuslly

    Looking for extended lug studs

  6. 9812VDuslly

    Looking for extended lug studs

    My inners Are both steel. My wheel hub bore is 130mm and for the life of me I can't find what these went on originally to try and find longer studs lol
  7. 9812VDuslly

    Looking for extended lug studs

    Don't know if this goes here...didn't see a thread for wheels and tires. I'm looking for extended lug studs for the rear axle of my dually. I bought a set of nice 19.5 8x6.5 wheels and the rear lug studs are about an inch too short. I've looked everywhere online. I called ARPs custom shop...
  8. 9812VDuslly

    Short to Ground on 98 K3500 HL circuit pls help!

    Edit. Not it. Still was blowing #16 turn lamp and b/u fuse. Fixed it here : https://www.gmt400.com/threads/turning-steering-wheel-blows-turn-signal-fuse.63215/#post-1334446
  9. 9812VDuslly

    Turning steering wheel blows turn signal fuse

    Found it. After spending a day doing just that and going through the entire column harness and every wire I could grab without dropping the dash, the problem went away again. And then I hooked up my trailer and back it came. Turns out was a loose wire on the rear of the truck on the b/u light...
  10. 9812VDuslly

    Turning steering wheel blows turn signal fuse

    I've been trouble shooting wiring, swapping trucks etc since you were swimming around in your daddies balls. Check my other posts, clown. Can't trouble shoot something properly thats intermittent. Like most electrical problems are. Hence purchasing the MFS when the problem can't be replicated...
  11. 9812VDuslly

    Turning steering wheel blows turn signal fuse

    98 K3500. Turn signal fuse started blowing awhile ago when engaged. Now it blows whenever the steering wheel is turned too far one way or the other. I just replaced the multifunction switch. Not it. Still doing it. I'm at my wits end with this ****** truck. Shoulda bought a Toyota. Anyone...
  12. 9812VDuslly

    Short to Ground on 98 K3500 HL circuit pls help!

    Alrighty, so after some reading, thinking and tinkering I believe I narrowed down the problem. Initially, it appeared, whenever I would use my blinker my #16 fuse would pop. After paying closer attention it seems whenever I made a turn and the blinker trigger would catch, that's when my fuse...
  13. 9812VDuslly

    Short to Ground on 98 K3500 HL circuit pls help!

    Reviving a dead thread here. The HL problem just went away on its own. Stopped blowing fuses one day, and that was that. Recently my #16 fuse has been blowing. This is an internal problem in the plastic switch housing itself, ya? Cuz all the wires coming out the back of the connector on the...
  14. 9812VDuslly

    Short to Ground on 98 K3500 HL circuit pls help!

    Thanks Erik, I appreciate the reply. All fuses are good. Dash lights finally started to work. Randomly. But the dimmer on my gauge pod gauges does not. I gotta pull and check those next now. Then I'll go back through the HL harness and main harness and clean and reground everything. It...
  15. 9812VDuslly

    Short to Ground on 98 K3500 HL circuit pls help!

    I ohmed out the blue wire at the socket to the S119 splice. Good reading. I get resistance. #thatsferkinweird Retest bulb socket. I get good reading this time. Huh? I ohm out whole circuit. From bulb to female connector at firewall. From male connector at firewall to blue wire at cluster plug...
See more

Latest posts

Members online

... and 16 more.
Total: 1,932 (members: 66, guests: 1,866)

Forum statistics

Threads
64,441
Messages
1,394,120
Members
51,682
Latest member
Dannyhtx

Share this page

Top