Recent content by 97moneypit
-
9
97 GMC k1500 5.7 engine sensor connectors
omg... i didnt even think of that...- 97moneypit
- Post #8
- Forum: Engine Performance + Maintenance
-
9
97 GMC k1500 5.7 engine sensor connectors
I just wanna repair the wires as they are exposed- 97moneypit
- Post #6
- Forum: Engine Performance + Maintenance
-
9
97 GMC k1500 5.7 engine sensor connectors
i cant not find the EVO connector to purchase- 97moneypit
- Post #3
- Forum: Engine Performance + Maintenance
-
9
97 GMC k1500 5.7 engine sensor connectors
would anyone know that type of connectors are used on these trucks? i would like to repair some sensor connections. the wire is exposed right where the wires go into the connections and would just like to replace replace the terminals. also would anyone know what sensor is connected right at...- 97moneypit
- Thread
- Replies: 7
- Forum: Engine Performance + Maintenance
-
9
Eng 1 fuse blowing
after 3 days of no luck i purchased the Haynes repair manual. according to their wire diagrams ENG 1 fuse feeds the following Evap can vent Evap can purge O2 sensors air injection (which I believe i don't have ) Cam sensor i did not check the Cam sensor. when i bought this pile of...- 97moneypit
- Post #18
- Forum: Engine Performance + Maintenance
-
9
Eng 1 fuse blowing
I got it apart and checked inside. I see no issues I have just wiggled the whole harness multiply times. I think the short is going to be 2 wires together I got it apart Checked all around there- 97moneypit
- Post #13
- Forum: Engine Performance + Maintenance
-
9
Eng 1 fuse blowing
Page 19 i am pretty sure thats for diesels According to page 15. Evap canister vent Evap emissions canister purge Maf Cam sensor All o2 sensors I have all these disconnected I'm thinking about just running an over lay harness...- 97moneypit
- Post #5
- Forum: Engine Performance + Maintenance
-
9
Eng 1 fuse blowing
97 gmc k1500 5.7. Eng 1 fuse is shorted I am going crazy. Disconnected all sensors on eng. Disconnected all 02 sensors. Disconnected all ecm connects. Injectors disconne I'm getting short to ground on eng 1 fuse. I have wiggled the harness all the way to the trans and back still no luck. Is...- 97moneypit
- Thread
- Replies: 17
- Forum: Engine Performance + Maintenance
-
9
Blinker issues
Some one please help me. Im going to burn drive this truck off a cliff. 97 gmc k1500 Swapped all lights to leds Engine off. All lights work fine. Engine on. Left blinker works fine with headlight switch in all positions Right blinker only works with the headlights in the off position...- 97moneypit
- Thread
- Replies: 3
- Forum: The Garage
-
9
97 5 7 vortec spider injector to mfi
I bet these are all the same part.... just rebranded- 97moneypit
- Post #5
- Forum: Engine Performance + Maintenance
-
9
97 5 7 vortec spider injector to mfi
Seems likes it's time to replace my injectors. Everything im seeing is to switch it to the mfi spider injector. Im looking and the only brand I'm really seeing is standard motor products. It looks just like the delphi one.. and I'm guessing it is. Rockauto.com 1aauto.com Amazon. Com All...- 97moneypit
- Thread
- Replies: 4
- Forum: Engine Performance + Maintenance
-
9
97 gmc 5.7 p300
Im thinking injectors because I do also get p0303 most of the time with p0300. Probably end up just doing them both and call it done. Whats a good upgrade for injectors ?- 97moneypit
- Post #16
- Forum: Engine Performance + Maintenance
-
9
97 gmc 5.7 p300
Any suggests what to check next ? Or what it could be.- 97moneypit
- Post #14
- Forum: Engine Performance + Maintenance
-
9
97 gmc 5.7 p300
Fuel pressures ( new fuel filter ) ENGINE COLD key on engine off 55-58 psi Idle - 3000 rpm ( steady rev up ) 45-48 psi quick snaps of throttle 55-58 psi engine off leak down 1 PSI drop every 30 secs ENGINE HOT key on engine off 55-58 psi idle - 3000 rpm ( steady rev up ) 45-48 psi...- 97moneypit
- Post #11
- Forum: Engine Performance + Maintenance
