-
-
JJDGMC replied to the thread I love plastic engine parts!.Btw if you run your truck hard the plastic will not hold up either way.
-
JVise grips and pull while twisting would be the first thing I'd do. Assuming it comes out, I'd chase the threads with a tap and insert a...
-
JJDGMC replied to the thread Low voltage at fuel pump.What are the wire colors of the truck harness? The connector is on top of the frame rail. The picture shown is the fuel pump wiring.
-
JJDGMC replied to the thread I love plastic engine parts!.Buy a cast aluminum timing cover as a backup. Once you have it in hand have at it. Make a wedge by grinding down a flat piece of metal...
-
JJDGMC replied to the thread 93 305 Rough Start Up.What model truck? Transmission? check engine light? Fuel filter age? Injector spray pattern? Strong spark?
-
JJDGMC replied to the thread Low voltage at fuel pump.Engine and transmission type? Do you have dual fuel tanks? You may have an oil pressure-sending unit tied into the fuel delivery system...
-
JFigure I’d start one of these. Will be slow going for a bit. Plans are: Upgraded audio Tint Exhaust 5/7 drop Rust repair Wheels/tires...
-
JJDGMC replied to the thread 3/4 Ton of fun - ‘95 Sierra.What I mean is wherever the splines land - you should make a dimple/flat spot where the set screw is contacting the steering gear input...
-
JJDGMC replied to the thread 3/4 Ton of fun - ‘95 Sierra.Is that an aftermarket steering shaft? If so, I’m guessing you checked the base of the steering shaft to make sure it’s fitted properly...
-
JNice recovery! I'm of the opinion that wiring harness failures are similar to the rusty areas that you repaired. That is, people think...
-
JRack installed and loaded up
-
JJDGMC replied to the thread 3/4 Ton of fun - ‘95 Sierra.That’t not normal. Hopefully it’s just lash not set properly. How much travel is there at the steering wheel to get it to clunk? If...
-
JJDGMC replied to the thread How could I fix this.Indeed it is, but it can be repaired. Invest in some equipment and start honing your skills. Years ago I purchased my 91 GMC C2500...
-
-
JJDGMC replied to the thread How could I fix this.I had the same issue on my 91 C2500 8ft bed. I just fabricated independent mounts.
-
-
JTry undoing the bolt at the top and the rag joint at the bottom, remove the two shafts from the truck, and explore how they connect. On...
-
-
Loading…
-
Loading…
Staff online
-
kennythewelderOfficially Retired, B31-3 (6-G) certified welder.
Members online
- the_elegant_fox
- seanb
- Chevy66driver
- patrick5050
- Rexall
- 68corvair
- Connorpod
- That black gmt
- bingobobby
- aldang25879
- Greenwood90
- VIKING_MECHANIC
- Carlaisle
- scott2093
- FLGS400
- Dame Dog
- 98BlackSierra
- Hosstyle Motorsports
- Salty K1500
- jp44
- so9956
- 95OBSMan
- Thatlowchevy
- smdk2500
- 95C1500
- Blue90
- schester04
- Rnelson698
- GeorgiaMtnClimber
- gchavonne
- Teddysvam
- roadkill79
- termite
- Zd92
- Dirkadirka875
- kennythewelder
- BonestockK1500
- Justsomeguy
- packer0440
- QBallz
- Komet
- Daly
- Knuckle Dragger
- isla bama
- Shawnmcsweeney
- bluex
- 99xcss4
- 94WarHorse
- Gotcrits
- L31MaxExpress