'94 GMC "The Blue Wonder" build

[95C1500]

it can. It has one it just isn't in the right spot to fill the gap

 

[Ruger_556]

Haven't posted in this thread for awhile, fixed a few little things. Valve cover gaskets, water pump, lower rad hose, and the fan clutch. Started to wash the engine bay, one of these days I'll detail it out a little nicer.

You must be registered for see images attach

Moved my spare parts storage from my toolbox into the garage, I can see the bottom again!

You must be registered for see images attach

Drove it down to my folk's land today.

You must be registered for see images attach

These came in the mail, might mount and wire them tomorrow. I have a couple parts for my radio sitting around that I should put on too.

You must be registered for see images attach

 

[Lordkay972]

WeatherTech floor liners... Technically for a Suburban but the driver's side fit's perfectly. Passenger side must use a different door pillar but it's not that far off

You must be registered for see images attach

You must be registered for see images attach

Just read the whole thread. Love the truck, had to explain why your mats don't for though! Burbs have an a/c duct running along the tranny tunnel for rear a/c, which makes the hump a little wider.

 

[Ruger_556]

Just read the whole thread. Love the truck, had to explain why your mats don't for though! Burbs have an a/c duct running along the tranny tunnel for rear a/c, which makes the hump a little wider.

Thanks Ah, that makes sense...

Put in an LED dome light bulb awhile back, I don't think I ever posted it in here.

You must be registered for see images attach

Got the fog lights installed and wired the other day, very impressed with these.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[Lordkay972]

Thanks Ah, that makes sense...

Put in an LED dome light bulb awhile back, I don't think I ever posted it in here.

You must be registered for see images attach

Got the fog lights installed and wired the other day, very impressed with these.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

What size bulb did you use?

 

[Ruger_556]

What size bulb did you use?

I used this one http://www.ebay.com/itm/271047799879?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT

 

[Ruger_556]

Most of the parts are here for my A/C, just waiting on the accumulator now. Got a new updated steering shaft and drivers door weather stripping too, still need to order the passenger side.

You must be registered for see images attach

 

[Ruger_556]

New steering shaft, the A/C is sadly an ongoing saga...

You must be registered for see images attach

 

[Ruger_556]

I guess I could update this thread now and again, Things that have happened in the last month...

A/C works finally, not enthused with the quality of AC Delco parts though. Namely the hoses which are clearly exactly the same as what NAPA sells, are not the same as the originals, run into the intake piping, and don't fit without a lot of work. Next time I might just have a set custom made up. The condensor was a nightmare of it's own...

You must be registered for see images attach

After fixing the high pressure switch connector that was causing issues

You must be registered for see images attach

11 blade fan, a lot quieter and the A/C works better in town.

You must be registered for see images attach

New belt and tensioner

You must be registered for see images attach

Wiped the down the interior, it needed some attention due to being the current daily driver.

You must be registered for see images attach

Put almost 1,000 miles on the truck this week. About 50 of those were on forest service roads so the clearcoat is scuffed up a bit from a few narrow sections, need to wash it and buff it out.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[Torchred]

Do you have a part # on the 11 blade fan?